C8OE-A cobra jet flywheel. Surfaced both sides. Bolt holes for 11.5 clutch are good. New ring gear. Has minor rebalancing, that can be corrected by removing weight if needed. 300- plus shipping. 863-618-7754
- Welcome to SAAC Forum.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages1
#2
Parts For Sale / Re: 1969 351W C9OE 8K18 Long Block
September 29, 2018, 07:12:25 PM
I see that with Keith's distributor and Wedgemans intake manifold this looks like it could become a reasonably correct 69 GT 350 engine... Just sayin.
#3
Parts For Sale / CJ RODS CJ FLYWHEEL FORGED PISTONS C6AE-R GT head
September 28, 2018, 10:27:32 AM
C7AE-B police GT500 KR500 CJ connecting rod set. 13/32 bolts. Polished beams, shot peened. Re-sized. 400-
C8OE-A CJ Flywheel new ring gear resurfaced. Has some minor rebalance. 400-
C6AE-R Cylinder head. Bare, Clean, Only one. Has new guides cut for 1/2" positive seals. 14 exhaust bolt pattern. ALL bolt holes are good. Stock seats. Installed heights look reasonable. 250-
B&M Hole Shot 40412 2400 FE 428 C6 Torque Converter Low miles, in sealed storage, clean. 200-
9 3/8" open carrier 31 spline for full size Ford/Merc clean in good shape. 100-
Pics available 863-618-7754 shipping is additional at cost.
C8OE-A CJ Flywheel new ring gear resurfaced. Has some minor rebalance. 400-
C6AE-R Cylinder head. Bare, Clean, Only one. Has new guides cut for 1/2" positive seals. 14 exhaust bolt pattern. ALL bolt holes are good. Stock seats. Installed heights look reasonable. 250-
B&M Hole Shot 40412 2400 FE 428 C6 Torque Converter Low miles, in sealed storage, clean. 200-
9 3/8" open carrier 31 spline for full size Ford/Merc clean in good shape. 100-
Pics available 863-618-7754 shipping is additional at cost.
#4
Wanted to Buy / Re: 1969 cj stuff
September 14, 2018, 05:39:13 PM
Do you need a correct flywheel? In the shop now getting a surface and new ring gear.
#5
Parts For Sale / Re: 1967 428 shortblock C6ME-A 6J29
September 13, 2018, 12:23:30 AM
Central Fla. Last block I shipped from here to syracuse ny was about 1000 miles 125-
#6
Parts For Sale / Re: 1967 428 shortblock C6ME-A 6J29
September 12, 2018, 10:25:47 PM
Added some new options..
#7
Parts For Sale / 1969 351W C9OE 8K18 Long Block
September 04, 2018, 01:47:16 PM
New Fresh 351W Long block
C9OE-B block date 8J18
C9OE heads date 8J26, 8K18
Exhaust ported
C9OE rods
Screw in freeze plugs and galley plugs. Polished lifter valley. Line honed, decked
L2378 .040 forged pistons undamaged lightly used in spec.
9.25 cr
Arp main studs
King bearings
M83HV oil pump arp
bolts and HD oil drive
Hydraulic flat tappet .485" lift 272 dur 216@.050 110 LSA 15423678
1.6 roller rockers
moly retainers
1.84/1.54 New valves
Exhaust is ported, hard seats.
C1010 pushrods
No intake, valve covers, distributor, water pump or balancer. Built and ready to ship.
3500- plus LTL shipping
863-618-7754
C9OE-B block date 8J18
C9OE heads date 8J26, 8K18
Exhaust ported
C9OE rods
Screw in freeze plugs and galley plugs. Polished lifter valley. Line honed, decked
L2378 .040 forged pistons undamaged lightly used in spec.
9.25 cr
Arp main studs
King bearings
M83HV oil pump arp
bolts and HD oil drive
Hydraulic flat tappet .485" lift 272 dur 216@.050 110 LSA 15423678
1.6 roller rockers
moly retainers
1.84/1.54 New valves
Exhaust is ported, hard seats.
C1010 pushrods
No intake, valve covers, distributor, water pump or balancer. Built and ready to ship.
3500- plus LTL shipping
863-618-7754
#8
Parts For Sale / 1967 428 shortblock C6ME-A 6J29
September 04, 2018, 01:17:27 PM
67 FORD FE 428 Short Block 6J29 Fresh build
C6ME-A 6J29 .030 4.16 bore. A scratch block. Bored and properly stored years ago. Oil galley mods. Does not have extra internal webbing. No cracks, no sleeves, no welds, bored .030 with 0 miles. Block is no longer available.
1U standard NOS crank. Original std/std, never been cut, never welded, never been run. Still in cosmoline. Available separately for 1250-
L2303 .030 forged pistons with light use, Inspected for wear, no damage and in specs. Have light scratches on skirts. Fine for polish and re-use. Yields 10.34 CR with stock 72cc heads.
C7AE-B Rods stock 428 3/8" bolts
King bearings, moly rings, roller chain, freeze plugs, 230 dur @.050 .520" cam with hydraulic lifters. Cam break in service utilized and degreed. Choice of color. No tins, timing cover, distributor, balancer or any pumps. Allow two weeks for shipping LTL to a trucking terminal near you. Call 863-618-7754 for a shipping quote to be paid before shipping.
3500- plus shipping
Matching C7AE-A 6K31 cylinder heads available. New GT size valves, springs, moly retainers. Exhaust has hard seats, ported and drilled for 16 bolts. Could add one GT bolt location (above the starter). Add 750- installed.
C6ME-A 6J29 .030 4.16 bore. A scratch block. Bored and properly stored years ago. Oil galley mods. Does not have extra internal webbing. No cracks, no sleeves, no welds, bored .030 with 0 miles. Block is no longer available.
1U standard NOS crank. Original std/std, never been cut, never welded, never been run. Still in cosmoline. Available separately for 1250-
L2303 .030 forged pistons with light use, Inspected for wear, no damage and in specs. Have light scratches on skirts. Fine for polish and re-use. Yields 10.34 CR with stock 72cc heads.
C7AE-B Rods stock 428 3/8" bolts
King bearings, moly rings, roller chain, freeze plugs, 230 dur @.050 .520" cam with hydraulic lifters. Cam break in service utilized and degreed. Choice of color. No tins, timing cover, distributor, balancer or any pumps. Allow two weeks for shipping LTL to a trucking terminal near you. Call 863-618-7754 for a shipping quote to be paid before shipping.
3500- plus shipping
Matching C7AE-A 6K31 cylinder heads available. New GT size valves, springs, moly retainers. Exhaust has hard seats, ported and drilled for 16 bolts. Could add one GT bolt location (above the starter). Add 750- installed.
Pages1