Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - tater_51

Pages: [1] 2
1
Wanted to Buy / Re: 67 Shelby Parts for 289
« on: June 10, 2022, 06:15:20 PM »
Hi, Are you looking for an S2MS or S7MS intake?  Thermactor  or non thermactor heads?  What date on the heads?  I have a 67 engine I'm probably going to part out.  Let me know what date your looking for, I might have a lot of the parts you need.  Terry in Michigan

2
1967 Shelby GT350/500 / Re: Identifying 67 valve covers
« on: June 07, 2022, 05:06:56 AM »
Thanks, that's what I had thought, just didn't want to misrepresent them.

3
1967 Shelby GT350/500 / Identifying 67 valve covers
« on: June 06, 2022, 08:23:35 PM »
I have a pair of covers off a 67 I purchased a long time ago.  Not sure if they are original or reproduction.  They are not "Buddy bar".  I've included a couple photos.  The oil baffles have also been removed.

4
Wanted to Buy / Re: Wanted: 289HP distributor and 67 GT 350 carburetor
« on: February 23, 2022, 06:08:35 PM »
e-mail sent

5
Parts For Sale / Re: 64 hipo balancer
« on: January 08, 2022, 10:20:37 AM »
Now $425 shipped in U.S.  SOLD

6
SAAC Forum Discussion Area / Re: 67 oil pump identification
« on: January 01, 2022, 07:34:41 PM »
Thanks!

7
SAAC Forum Discussion Area / 67 oil pump identification
« on: January 01, 2022, 12:13:53 PM »
Any ideas on the stamping on this pump, taken off a 67 hipo block?

8
Parts For Sale / 64 hipo balancer
« on: January 01, 2022, 12:06:21 PM »
64 hipo balancer for sale.  The date code was discussed on this forum if you search it, most likely H4 but unknown for sure.  No hammer marks, slight pitting on some areas. Small area appears ground away on backside, see photo.  $525 shipped in lower 48.

9
Wanted to Buy / Re: WTB a pair of 289 hipo heads with 6M22 to 7A31 casting date
« on: November 05, 2021, 10:56:23 AM »
Thermactor or not?

10
SAAC Forum Discussion Area / Balancer date
« on: May 18, 2021, 05:45:33 PM »
I have had this balancer since the 60's.  It was on an early hipo Fairlane.  It's a C5OE balancer.  Help with the date code stamp?  It looks like I4, but Ford did not use "I" for their dating.  I don't find any other stamping on the balancer.  Thanks

11
SAAC Forum Discussion Area / Shot in the dark!
« on: March 01, 2021, 09:35:49 PM »
It's probably been 5-6 years since I posted a photo of this 67 block.  It's kind of a mystery, but always hoped someone might know it's origin.  Thought I'd try it again.  Came out of a street rod about 15 years ago.  Had S7MS intake, cobra valve covers, 6M22 heads, LeMans camshaft, all hipo internals, hipo pump (water), distributor, everything pretty much date matched.  The block's cast date was ground off and the block was stamped on the boss next to the water pump (see photo's).  I had papers with it dating back to machine work in the early 90's but no help.  7B14 machine date, 7B15 assembly date.  Maybe someone recognize the stamping?

12
Wanted to Buy / Re: WTB: 67' Shelby Parts...
« on: February 06, 2021, 08:05:49 PM »
Are you looking for a single 67 hipo head?  Disregard, I see your looking for a non-smog head, this is dated 6M22 and is a plugged thermactor head.

13
Wanted to Buy / Re: Need carburetor and dual point distributer for HERTZ 350 Rent a Racer
« on: January 31, 2021, 08:36:19 PM »
What date distributor are you looking for?

14
Wanted to Buy / Re: WTB: 4100 carb 'M' primary booster/venturi
« on: July 09, 2020, 12:16:35 PM »
Might also post on Ed'sCarburetorForum, I've had good luck locating some hard to find 4100 parts there.

15
Wanted to Buy / Re: 67 289 block dated jan-feb
« on: November 11, 2019, 06:01:03 PM »
Looking for a C5 block.  The current block I have is dated 7B15 and is a C5 casting.  Thanks

Pages: [1] 2