Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - PR

Pages: [1] 2 3 ... 5
1
SAAC Forum Discussion Area / Re: Bellhousing interchange 302-351
« on: April 01, 2020, 09:46:31 AM »
Thanks, that is what I thought, I have a 164 tooth bellhousing, I will buy a 28oz  flywheel for 11" clutch, I am converting a 69 mach 1 automatic to a 4spd , will the automatic starter work with the 4spd, like the FE, or are there 2 different starters, thanks again

2
SAAC Forum Discussion Area / Bellhousing interchange 302-351
« on: March 31, 2020, 11:20:28 AM »
Will a 302 4spd bellhousing work on a 351 w or is 351 specific

3
1968 Shelby GT350/500/500KR / Drive shaft length chart
« on: March 19, 2020, 01:04:38 PM »
Mustangtek use to have a chart on drive shaft length, but I can't locate it now, does any one have it to share, I need a new one built for a new project, thanks Pete

4
1966 Shelby GT350/GT350H / Re: How many on this site have a red Hertz?
« on: February 16, 2020, 08:42:04 PM »
There was one I seen in a garage in Santa Rosa ca, red, gold stripes auto, he said it was a hertz car, very original, but engine had issues that's why it was parked and why this guy got the car

5
Wanted to Buy / Re: Small block dual quad intake
« on: February 09, 2020, 11:43:51 AM »
I have a setup rudo9@comcast.net

6
Wanted to Buy / Re: 68 GT500 Fan Shroud
« on: January 22, 2020, 10:33:12 AM »
There is an nos one on the 428 cobra jet forum 1100.

7
1968 Shelby GT350/500/500KR / Re: Export brace question
« on: December 28, 2019, 09:50:54 AM »
Thanks Bob

8
1968 Shelby GT350/500/500KR / Export brace question
« on: December 27, 2019, 10:50:52 AM »
I need an export brace for one of my mustangs and I have seen junk that doesn't look like the ford one on my Shelby, stamping was different, who makes a good repo that fits and looks like an original

9
1968 Shelby GT350/500/500KR / Re: '68 KR - Clutch
« on: October 29, 2019, 10:24:08 AM »
You can get the ram clutch from Brent Lynkens Motorsport, ram power grip HD, I have used them on 2 ,427 street cars and a CJ mustang, if you're hard on clutches this one can take a beating and lasts

10
Wanted to Buy / Re: '67 HiPo Connecting Road
« on: October 27, 2019, 01:38:52 PM »
I have a nos one, send email to rudo9@comcast.net and I can send pictures
I believe mine is pressed pin, no squirt oil hole on small end

11
Wanted to Buy / Re: BOUNTY : Looking for these cars
« on: August 23, 2019, 03:37:22 PM »
Pete, what is special about these, paint?, if so I know of a 69 350 auto in a garage in San Mateo ca it is orange I believe original owner

12
Wanted to Buy / Re: WANTED: 68 10 spoke spare wheel
« on: August 06, 2019, 02:19:33 PM »
My wheel has sold

13
1968 Shelby GT350/500/500KR / Re: Radiator pic
« on: August 06, 2019, 02:17:16 PM »
Another picture

14
1968 Shelby GT350/500/500KR / Re: Radiator pic
« on: August 05, 2019, 10:12:41 PM »
You need to send me a email so I can send you pictures, rudo9@comcast.net

15
1968 Shelby GT350/500/500KR / Re: Radiator pic
« on: August 05, 2019, 04:11:15 PM »
I have my original in storage if you haven't got pictures yet, mine is From 02602 350 4spd, non a/c, send email to rudo9@comcast.net and I can send soon, Pete

Pages: [1] 2 3 ... 5