Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - nightmist67

Pages: [1] 2 3 4
1
1965 GT350/R-Model / Re: Spare Tire Cover
« on: April 02, 2020, 11:23:30 AM »
I would also like to purchase one when they become available.

2
1965 GT350/R-Model / Spare Tire Cover
« on: March 29, 2020, 03:07:15 PM »
Several months ago there was an indication that someone may make a short run of accurate reproduction spare tire covers for 1965 GT350s.  Is there any update on the status of that effort with respect to who, when, and for how much?

3
Bob Gaines -

I tried posting photos on the website, but I was unsuccessful.  I sent you a separate PM with photos.  Thanks for the response that, in your opinion, it is likely an original sand cast lid.

4
My sand cast lid has the straight leg "R" and a 3/16" space between the base of that leg and the base of the "A".

5
Bob Gaines -

The  lettering on my lid matches your image.  When I enlarge your lid image, it looks like there is a very faint rectangular border around the lettering.  Is that true for all original sand cast lids?  When I run a finger along the perimeter of the lettering on my lid, it feels as if the metal is very slightly raised, but there is no distinct rectangular border.

6
Bob Gaines -

Could you be more specific regarding the design or shape of the letters?  Could anyone provide images of an original sand cast "COBRA" air cleaner lid for reference?

7
When I bought my 1967 GT500 about 20 years ago it had a die cast air cleaner base and sand cast lid.  I would like to determine if the sand cast lid is original or a reproduction.  There in no engineering number on the underside, and there is no obvious evidence of a "box" around the "COBRA" lettering.

8
Parts For Sale / 1965 - 1967 Mustang/Shelby Parts
« on: December 25, 2019, 10:41:41 AM »
1965/66 NOS front bumper:  $375  (SOLD)
1965/66 NOS front bumper brackets, pair:  $200
1965/66 radio noise suppressors, original, used (alternator and voltage regulator versions):  $25 each
1966(?) NOS low tone horn:  $30  (SOLD)
1965 grille, original, used:  $125
1965/66 NOS gasket set, engine valve grind, C3AZ-9441-A:  $60

1967 GT500 air cleaner base, original, used:  $300  (SOLD)
1967 GT500 air cleaner filter, original, used:  $300
1967 Shelby rear quarter panel fiberglass end caps, used, original, right and left:  $750
1967 NOS oval air cleaner lid ("Shelby" casting):  $300
1967 thermactor smog pulleys, original, used:  $150 (C7SE-9B447A); $65 (C7OE-9B447B)

Shipping and insurance extra.

9
1967 Shelby GT350/500 / Re: GT500 Engine Detail Question
« on: October 10, 2019, 03:23:24 PM »
The photo confirms the hose and check valve/flame arrestor in way of the oil breather and air cleaner.  Can anyone provide a photo of and/or part number for the check valve/flame arrestor for this application?

10
1967 Shelby GT350/500 / GT500 Engine Detail Question
« on: October 10, 2019, 09:57:15 AM »
For a 1967 GT500 with thermactor emissions system, what components connect the port on the oil breather tube to the elbow fitting on the bottom of the air cleaner base?  Are there any photos that show those details?

11
Concours Talk / Re: 1967 GT500 Engine Block Paint Overspray
« on: October 08, 2019, 01:47:20 PM »
Overspray on intake was applied during engine rebuild.

12
Concours Talk / 1967 GT500 Engine Block Paint Overspray
« on: October 07, 2019, 02:03:02 PM »
Should there be any engine block paint overspray on the base of the distributor, distributor hold down clamp, and/or hold down clamp bolt?

13
1965 GT350/R-Model / Re: Accurate Reproduction Spare Tire Cover
« on: September 24, 2019, 11:48:00 AM »
Based upon the above responses, it sounds like possibly two sources may make limited runs of the spare tire cover sometime in the future.  Is there any estimate when each potential vendor will produce them and the associated cost of the cover?

14
1965 GT350/R-Model / Accurate Reproduction Spare Tire Cover
« on: September 20, 2019, 10:51:09 AM »
Does anyone make an accurate reproduction spare tire cover for the 1965 GT350?  I know of a recent attempt to do so.

15
Does the hose that connects the gulp valve to the port on the top of the smog filter canister have the same "alligator" texture as the other hoses?  Are any clamps used on either end of the hose?

Pages: [1] 2 3 4