Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - paul

Pages: [1] 2 3 ... 7
1
Wanted to Buy / Hipo air cleaner base
« on: April 07, 2021, 11:34:34 PM »
Wanting to buy air cleaner base or if necessary base and top assembly for an early California emissions Hipo mustang, production date late calendar year 64.

2
Parts For Sale / Re: 65/66 Shelby & Mustang parts for sale
« on: April 05, 2021, 03:32:23 PM »
Sheet metal is sold. Thank you Jesse and Darren.

3
Parts For Sale / Re: 65/66 Shelby & Mustang parts for sale
« on: April 05, 2021, 01:54:03 PM »
2nd top loader (HEH-BX) and 1965 gt 350 axel housing are sold, thank you Tim.

4
Parts For Sale / Re: 65/66 Shelby & Mustang parts for sale
« on: March 29, 2021, 01:59:09 PM »
Top loader sold(HEH-T) sold, thank you Greg.

5
Parts For Sale / Re: hipo heads for sale
« on: March 26, 2021, 09:02:37 AM »
Iíd like to see pictures please. Send to paulrmarvin@icloud.com.

6
Thank you Rick and Brian.

Brian, you sir are 100% correct. My dad is 85 and I would consider him my best friend. I am blessed not only to have a very close relationship with him but also blessed by being aware and appreciative of it in real time.

Rick, the motor in 213 at the time we went for our ride is still in it. Itís basically a stock 1965 hipo 289 with a modern solid lift camshaft. That specific cam was recommended to me by the gentleman who restored my vintage Weber setup(its lobe separation is perfectly suited for the Webers to perform). The combination of camshaft, roller rockers, and valve springs/keepers/retainers make for an excellent street engine. Even with just the 4V Holley instead of Webers, it performs exceptionally!

The race motor, which is also included in the sale, is very aggressive in comparison. At over 14 to 1 compression, roller camshaft, and highly finessed heads, it completely changes the experience of driving the car. With it installed, the car attracted even more attention(good and bad)! In full disclosure, I initially decided to swap engines because even just idling the motor to get out of my neighborhood, the car would cause all my neighborís horses to panic and stampede to the back of their properties trying to get away.

7

213 currently has a stock hipo 289 motor with all the R model trim installed. Along with the car at auction is an additional race engine on a rolling dolly. The race engine is also a date appropriate hipo 289 with lots of goodies for higher performance. Itís dynoed in at 352 ft/lbs torque and 375 horse power

8
Thank you 427heaven.
I have just about completed the conversion of a 1200 square-foot shop in my backyard into the ultimate man cave/apartment with the intent of moving my dad into it when heís ready.
I am very proud of how it looks. I did most of it myself and it turned out better than expected.
213 looked great in there. Even though my dad lives only 5 miles from my home, I think him living there instead of 213 is the best possible outcome.

9
213 in its old hangout.

10
Parts For Sale / Re: 65/66 Shelby & Mustang parts for sale
« on: March 03, 2021, 09:47:15 AM »
Parts description revised. Thank you, Paul.

11
Parts For Sale / Re: 65/66 Shelby & Mustang parts for sale
« on: February 13, 2021, 09:36:13 AM »
Greg, the rt side 1/4 is still a available but I would prefer not to split the pair. Thank you, Paul.

12
1965 GT350/R-Model / Re: R Model Heads, Cam and Intake
« on: February 05, 2021, 12:58:23 PM »
Earl J,
   what type of piston and what compression ratio is your motor with those 47cc heads?
Thank you, Paul.

13
Parts For Sale / Re: 65/66 Shelby & Mustang parts for sale
« on: January 21, 2021, 05:27:28 PM »
Thank you Dominic and Rick.

14
Parts For Sale / 65/66 Shelby & Mustang parts for sale
« on: January 20, 2021, 01:30:13 PM »
NOS Lft & Rt red oxide fastback 1/4 panels.  $3500/pair SOLD
NOS front & rear red oxide valances and stone guard.  $900 SOLD
Small cobra S1MS COBRA intake.   $2500
LIST 3259 715CFM DATED 513.  $4000 SOLD
Hipo air filters top and bottom(no date).  $250 SOLD
1965 GT 350 axel housing with hipo axels, no backing plates or drums.  $2000 SOLD
Close ratio top loader 4 speeds HEH-BX with Ford shifter box, rods, ďTĒ handle lever, and ball.  $1700 SOLD
Hipo Mustang rear leaf springs #C4ZA5556S dated 315E5/299E5(Oct/Nov 65 dated).  $1500
Complete hipo 289 engine assembly running takeout, 5E26 block/5D27 heads, VIN stamped 5R09K232XXX. Comes with: cast iron intake, steel oil pan, hipo motor mounts, fan to bell housing (no carb, aircleaner, valve covers, distributor, alternator, pulleys or brackets) $8000
Partial(90%) Fold down seat assembly and trap door  $200
65/66 mustang 1/4 vent assemblies   $200
66 Shelby 1/4 window pieces.  $100

Pictures/date codes available on request. Paul @817-691-0159, paulrmarvin@icloud.com
Paul Marvin @ paulrmarvin@icloud.com, 817-691-0159

15
1965 GT350/R-Model / Re: R model guages
« on: January 08, 2021, 02:52:48 PM »
Fellas, Iím sorry but Iím still confused. So just to clarify the discussion for my feeble mind:

1) Jerry, your last posting ends without a period or question mark. Are you asking if the R model Tach was made by a different company or are you stating that it was in fact made by a different company?

2) 98SVT, I was under the impression the tachometer in the R model was the same as the street car(Faria) but just the needle color is white. Iíll look through what I can find from back in the day to see if the Tach is listed as a Stewart Warner piece.

3) Bob, are you saying the R models used S.W. tachometers?

Pages: [1] 2 3 ... 7