Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Shelbypat

Pages: [1] 2 3 4
1
1969-1970 Shelby GT350/500 / Re: Designers of the fiberglass
« on: August 09, 2020, 09:13:03 AM »


There was an office / shop in Ionia inside the COE building

What is COE building ?

Patrick

2
1968 Shelby GT350/500/500KR / Re: 12v yellow top coil
« on: August 01, 2020, 09:47:36 PM »
Happen samething to me. The repro run 15 min and fail. I bought a good original used and never miss for 12 years now.

Patrick

3
1967 Shelby GT350/500 / Re: BJ/BK Carbs Will Not Idle Down
« on: August 01, 2020, 06:08:00 PM »
Retight your intake hot. It can suck by underneath.
Patrick

4
1969-1970 Shelby GT350/500 / Re: ^69/70 white stripe kit
« on: July 31, 2020, 08:10:39 PM »
Branda performance would be a nice supplier...
For how long do you own your car  Rick ?
Patrick

5
1969-1970 Shelby GT350/500 / Re: First time I seen this
« on: July 30, 2020, 10:45:05 AM »
And the fastbacks will have Mach 1 hood pin holes in radiator support
Mine is a vert and has hood pin holes

6
1969-1970 Shelby GT350/500 / Re: New wiring no power to fuse block
« on: April 04, 2020, 06:44:07 PM »
Sulely someone here has pic of the back side of a Faria amp ?

7
1969-1970 Shelby GT350/500 / Re: New wiring no power to fuse block
« on: March 30, 2020, 08:34:13 PM »
The blue/red wire come out of fuse box going to instr light, clock light, radio light, heater light if that helps
+1 and ashtray light

8
1969-1970 Shelby GT350/500 / Re: New wiring no power to fuse block
« on: March 29, 2020, 07:47:31 PM »
I think a stud is missing behind your gauges for  bulbs ground !!! As your third pic wire should go.

9
1969-1970 Shelby GT350/500 / Re: New wiring no power to fuse block
« on: March 22, 2020, 08:31:41 PM »
If you have no power, it could be the ampmeter itself. You can jump both amp 10 gages wires together to test.

10
1969-1970 Shelby GT350/500 / Re: New wiring no power to fuse block
« on: March 20, 2020, 10:04:50 PM »
This one ? The red one on the selenoid?
Not suppose to be red. They are both black.

https://lib.store.yahoo.net/lib/yhst-13525187779972/ammeter.pdf

Here a pic of my old original one

11
1969-1970 Shelby GT350/500 / Re: Question about C6 case casting code
« on: February 13, 2020, 07:27:21 AM »
Tks
My car is built jannuary 30 1969. Does it mean that it should have more an A or B suffix ?
I know my trans is not the original one from the car as it was 4 speed when I bought it 28 years ago.

Patrick

12
1969-1970 Shelby GT350/500 / Re: Question about C6 case casting code
« on: February 12, 2020, 09:35:30 PM »
What does the last letter D mean on the casing?
On mine is:
C8OP 7006 D

TKS
Patrick

13
Wanted to Buy / Re: Short block for 1969 GT500
« on: December 06, 2019, 07:58:03 AM »
Ask on Facebook...Ford FE fanatics garage sale group.

Patrick

14
1969-1970 Boss 302/429 / Re: Dual exhaush gas sender wire hole
« on: October 25, 2019, 08:28:14 PM »
Jeff. This hole is located at correct and original location for the gas sender wire.  The yellow and white stripe one. But funny to see it rough like that. The way I can explain it is assembly line ran out of the side hole trunk floor and they installed standard floor without this hole and handmade it fastly.

15
1969-1970 Boss 302/429 / Dual exhaush gas sender wire hole
« on: October 23, 2019, 12:54:23 PM »
Hi, I have visited a friend's B2 1969 ground up restauration and saw the dual exhaush wire hole on the right trunk floor hand made and rough made. Anybody know something about it ?
Original body ane trunk floor.

Patrick

Pages: [1] 2 3 4