SAAC Forum

My KR finally has its motor in it. if anyone has time could someone take a bunch of photos showing where all thee plastic clips go that hold the wiring harness to shock towers and inner fender aprons, thanks in advance Mike

my cars DSO is 8D2975  "Home office Reserve ordering district under Domestic Special order number 2968" any clue what all that means?

Its been hot in florida this summer so progress has been slow, but fall is around the corner so what
did they use clear silicone, black silicone? or something else? on the upper and lower side scoops?

thanks in advance,

Mike

my car was ordered by Al Grillo Ford but a invoice change was made and car was delivered to and sold at Gotham Ford. i could probably have a sign shop to remake it for me. but does anyone know someone that may already have them or a good scan of it?

3 of my 6 taillight covers were lost due to 3 had rust so those were put elsewhere. I knew they were there somewhere and I would bump into the when I wasnt searching for them. So I started fixing the rust.

I moved it to my other shop for assembly.

ok my car had sport mirrors on when i got it. did all 68's have a remote drivers side door mirror. im at home today and my old door panels are my shop to look to see if there's a hole for the knob. or do i need to look at my Marti report to verify. thanks and sorry for all the questions.

Mike

My car had one on it when i took it apart. but looking for photos  of other cars i dont see any?
thanks in advance
Mike

i purchased this wiring from Pete over 10 years ago if i remember right. never took it out of the box. It was in my hot florida garage and the packing peanuts melted to it. My fault but luckily they cleaned up with a rag and a light coat of solvent.

i also went thru some parts i was givin back when i bought the car, i Found this box of Dynamite sticks with what looks like a shelby part number on it but i cant read it. not sure if these are nos or memorex.

i have a pair i bought years ago they have very slight scuff marks from being taken out of the boxes 200.00 plus actual shipping cost
located in Pensacola Fl. i also still have a 68 NOS front bumper. 450.00 thanks Mike

I was test fitting the taillight panel in my car today with all the lights in it. how does the wiring for the taillights go from inside the trunk to the taillights. ive misplaced my 2 large taillight covers. (they are here somewhere) did they have a hole for the harness to go thru? does the taillight harness run like the mustang across the tail panel  to the passenger side taillight?  thanks any pictures would be appreciated

Mike

i have my old valance and they are painted i see some photos where they are chrome? which is correct? thanks in advance Mike

Who makes the most correct aftermarket stripe kit?

Thanks Mike

Painted it a week or so ago. Then sanded with 800 and recleared it. The sanded with 2000, 3000 and 5000. Looks pretty good.

So i need a new gas tank, do i go with concourse correct replacement? or Scott Drake SS tank. is there any other options, i know ill be running good gas it just seems smarter to buy Stainless.  does anyone make a stainless one thats close to original?

thanks Mike

I have 2 NOS front bumpers for a 67 or 68 mustang/Shelby, 1 is in pretty good shape for nos the other looks good also but chrome has minor rust starting its very hard to see. NOS bumpers are not perfect and i know alot people have them done in show chrome. anyway im asking 550.00 for the better of the 2 and 425.00 for the other. plus shipping. im located in Pensacola, fl. pics are of the better bumper

I have 3 NOS front bumpers but I need a rear bumper, anyone  have a nos rear bumper they want to trade for a front bumper?

i bought this car from a friend back in 2004 over the years ive acquired a few stripe kits, one of them looks like it might be a GT350 nos kit but rolled up in it was a 500KR sticker that does not look correct with same 3m backing?

I painted my car last sunday. After 15 years of ownership. I hope the pictures show up.

Anyone out there that has bought new rear leaf spring and are happy with the ride height have a part number to order? i looked at npd and the only 1 i see for a 428 mustang states 1" lowering? i want a stock ride height. and i have my original set to use the bottom leaf with part number. thanks in advance. Mike