SAAC Forum

Some more garage finds nothing special
C9AF-U new kit in it, was running on mach1 but removed for DP Holley,$450 date 2266 sept 76
—-$S2MS-A setting for awhile but good condition $650 date 2148 aug 78- SOLD pending payment
C70F-B needs rebuild missing transfer tube $250 date 672 July 66
3310-2  needs rebuild $125
All + sipping or best offer, 707-849-0352, rudo9@comcast.net

Ok guys still finding stuff in spring cleaning, 2x4 setup with DOPF-u 70' carbs older blue thunder intake I believe had it for 30 + years carbs gone through complete w/ air cleaner and valve covers $2100, 1-nos 289 std rod $35, dual point dist. Motorcraft $500
All best offers + shipping, 707-849-0352 rudo9@comcast.net
EVERYTHING SOLD,EXCEPT Dual point dist

Very clean case & support 9108, January 8th 69, $650 , also Detroit locker 31 spline, $350 I believe nos, parts I received from lifetime ford employee who serviced 9" in the 70's at ford dealer S&C ford SF ca, all prices + shipping 707-849-0352, rudo9@comcast.net I also have axels if needed for mustang $500

Drivers side front ext 650$, nos drivers side lower scoop 700$, 68deck lid 900$, tail panel 900$ all plus shipping,
Rudo9@comcast.net will make package deal on everything

Deck lid and tail panel & headlight ext and broken scoops spoken for

This car always runs hot in traffic in the warm months, motor was rebuilt, new radiator installed, but I believe it's a standard water pump, looking for a HV pump, what's everyone using these days, thanks in advance for the input, it gets up to 220+ has HV thermostat,

67400F7A00764 , not mine, just seen it, 80k 427 4spf, not sure if it's been discussed here, car is in SD. Pete, on San Francisco Craig's list

Looking for drivers side A pillar molding or set,let me know Pete rudo9@comcast.net
The plastic inside molding

Found my stash of 68 hubcaps, looking to trade some up or down, I need a 69 rim blow steering wheel also looking for a cobra 1x4 repo air cleaner setup for a 69 mach 1, I need to keep 1 set for my 68 shelby, Pete, rudo9@comcast.net

I was wondering if the event next weekend is cancelled or not, the Sears point website appears that it is still going to happen, anyone have any info, thanks Pete

Let me know what you have, looking for ford parts, thanks
Rudo9@comcast.net

Will a 302 4spd bellhousing work on a 351 w or is 351 specific

Mustangtek use to have a chart on drive shaft length, but I can't locate it now, does any one have it to share, I need a new one built for a new project, thanks Pete

I need an export brace for one of my mustangs and I have seen junk that doesn't look like the ford one on my Shelby, stamping was different, who makes a good repo that fits and looks like an original

Let me know what you have

Let me know what you have, aluminum original only. Rudo9@comcast.net

Converting my 70 Mach 1 to PDB, is seems everything is unique to 70, the car is a original 4spd but drum brake, need support bracket and brake pedal and distribution block, I have everything else, Pete
rudo9@comcast.net, thanks

I am replacing all idlers and need to install new clutch bearing, system is charged and working r12, so I want to remove a/c clutch on car, I have everything apart and center bolt is out and have tried a puller kit but it didn't have the correct lug and center bolt to remove, I have not done this before and can use some advice on the correct way without damaging it, I believe it's a Pitts unit, thanks in advance,Pete

https://sfbay.craigslist.org/sby/pts/d/shelby-mustang-fiberglass/6770735385.html

Not mine, 68 fastback, looks original,but needs some work

Where or who should I contact for one of these units, PO modified my original dist and removed the vac advance unit, trying to put it back correctly, thanks Pete rudo9@concast.net

Car runs fine but tach not working, any ideas, it would not run if circuit not complete , I am thinking it's the tach itself, thanks