Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - lawrence67

Pages: [1] 2
1
Anyone have an idea the purpose and location of this rubber disc?
PL

2
1967 Shelby GT350/500 / Finally time for rocker stripes
« on: August 19, 2023, 08:56:07 AM »
 My 67 GT350 is finally ready for rocker stripes to be installed.  I need pictures and help with location for stripes.  I remember discussion in the past on location on front fenders ahead of the doors. I haven't been able to find good pics of straight on side view.
Is it me or is the "search" function a joke. Never had any luck with it.  What's the secret?  It just seems to suck.

Paul L

3
1967 Shelby GT350/500 / Any one have a source for odometer repair?
« on: July 15, 2023, 09:23:33 AM »
Did a search for odometer repair, nothing.  Anyone have a reliable source?
PL

4
1967 Shelby GT350/500 / Exhaust tip extension from valance
« on: May 21, 2023, 01:48:19 PM »
The extension of tip to valance seems, if memory serves, is 4.75".  Is that correct judges?
PL

5
Per subject of ammeter wiring harness clip all I can find is part of a kit at NPD has some but they look too short.  Maybe they'll work.  Can't seem to find a sure source.    ???

Paul L.

6
1967 Shelby GT350/500 / Position of heater hose strap p/n 18B465-1A
« on: March 16, 2023, 11:02:24 AM »
Cud someone please supply pic of the heater hose strap p/n 18B465-1A location on the RH spring/shock tower or the brace.
Thks.
PL

7
1967 Shelby GT350/500 / Front bumper attachment
« on: March 01, 2023, 12:53:30 PM »
Do all 67's have front bumper attached to front fender with small bracket and hardware on each corner?  With extention of nose and bumper brackets seems unlikely.  My bumper and fender has holes but no bracket or hardware when purchased in  81.  Car had been partially disassembled for repairs previously so anything is possible.
If answer is positive if anyone has  extra brackets please contact me pm  or email.
Thks PL.

king1@shaw.ca



8
1967 Shelby GT350/500 / Brake pedal stainless disc
« on: November 16, 2022, 08:13:15 PM »
I have 2 brake pad stainless discs. one has black painted letters and second has no paint and doesn't appear to ever have had paint. Both appear to have been installed at some time.  Which is correct for 67 brake pad on s/n 19xx with A/T?
Thks
PL

9
1967 Shelby GT350/500 / Gas Cap latch spring installation
« on: September 11, 2022, 01:53:36 PM »
Howdy all,
Anyone have a "trick of the trade" method of installing the pesky spring for gas cap latch, even a closeup pic of correct end result will help. The way I had it loop was over the lip.

Thks
PL

10
1967 Shelby GT350/500 / engine hood latch
« on: May 16, 2022, 01:08:37 PM »
 GT-350 s/n 1935, SJ build 4/67,SA build 6/67.  Which of the hood latches would it most likely have been installed, long or short?  Hood all glass, no louvers.
 
Lawrence67,
Paul

11
1967 Shelby GT350/500 / Rear spring shackle orientation??
« on: May 14, 2022, 12:33:56 PM »
I believe there was some discussion about direction lh and rh shackles and their fitment difference side to side and potential for exhaust interference.  Searched but nothing turned up.  Any hints??

Lawrence67
Paul

12
1967 Shelby GT350/500 / 289 pump-carb fuel line and bracket to water pump
« on: November 16, 2020, 12:43:56 PM »
Spent some time searching forum pages for info on above subject.  Info has been discussed but must have been on V1. Anyway I need fuel line and bracket to water pump for gt350 s/n 1935 w p/s & a/c.  Vendors seem to only have for 65-66 and w/o p/s. Might run under a/c compressor ok?  Any suggestions or help appreciated.  Close up pics of installation would help if I have to fab line.  Looks like Drake has bracket but not sure it's correct.  Seem to remember one of forum guys had made a correct looking one and would sell??  Ring any bells with anyone?
PL


13
1967 Shelby GT350/500 / Door speaker grill fabric
« on: June 08, 2020, 02:38:52 PM »
Has anyone found a source for the fabric that was glued to lower door grill at speaker hole on each door?  Mine are torn.
Paul

14
Pictures I've seen, some have dash pot installed and some don't.  Which is correct for S/N #1935 is CJ apr, SA jun delivery?  It also is A/T, A/C optioned.  Also, different Holley info has cfm listed as 715 and 725, is 715 correct?
PL

15
1967 Shelby GT350/500 / GT350 rad hoses, staples or not?
« on: March 31, 2018, 09:32:42 PM »
Marti has 67 SB rad hoses that have staples to locate wire clamps for SJ builds.  I thought this was a 68 only thing. Are these correct for 67s?
PL

Pages: [1] 2