Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - corbins

Pages: [1] 2 3
1
SAAC Forum Discussion Area / Shifter install
« on: January 09, 2022, 02:57:11 PM »
So I was given this plate and this shifter to install in the 69 SCJ I’ve been working on. However , I cannot find two plate holes , threaded or un-threaded that the shifter will line up with. Am I looking at incompatible components? Top loader of course.
Thanks

2
SAAC Forum Discussion Area / 69 SCJ install
« on: December 22, 2021, 03:05:42 PM »
I seem to have a mismatch between the Centerforce pieces and the ford clutch arm . Clutch arm is C8OA 7515 B. Throwout bearing is a Centerforce N1493. They are both suppose to be correct , but bearing will not fit the arm. Ive attached a couple of pics. Can anyone explain which is incorrect ?  Thanks !

3
SAAC Forum Discussion Area / SCJ oil filter adapter gasket
« on: December 17, 2021, 12:43:20 PM »
Does the SCJ adapter take the same gasket as a regular CJ adapter ?

Thanks !

4
The Lounge / Referral/suggestion needed.
« on: October 01, 2021, 10:33:53 AM »
Looking for a suggestion on an aftermarket radio for my 68. Been through 3 Custom Auto Sound units in 7 years. POS in my opinion. Has anyone had good luck with another brand? I know I can send the original out and have it modernized.

Thanks !

5
Ask a Registrar / Morrison Shelby
« on: August 18, 2021, 06:58:13 PM »
Is the vin/Shelby number known ??

6
Wanted to Buy / WTB- hockey sticks 1969
« on: August 12, 2021, 05:54:47 PM »
Looking for a pair of originals for a Non Fold down FB . Cant use any with wallered out holes though,  I have those already :)

Thanks

7
1969-1970 Shelby GT350/500 / 1969 500 Electrical question
« on: August 07, 2021, 11:35:52 AM »
Maybe stupid .... no problem , Is there any way or procedure for "bench testing" the console wiring prior to install ?

Thanks !

8
1969-1970 Shelby GT350/500 / 1969 dimmer switch position
« on: July 15, 2021, 12:05:56 PM »
Anyone have a pic ? This car got new floorpans , toeboards. Plug orientation is up ? right ? or left ? I have searched and couldnt find a pic on a 69 anywhere (:

Thanks, Steve

9
1969-1970 Shelby GT350/500 / 69 speedo cable routing
« on: July 02, 2021, 08:03:58 AM »
Quick question... speedo cable , 2 clamps to firewall or one? Have seen both ways , just one on the rt side, and also one on both sides of the tunnel.
Thanks

10
1969-1970 Shelby GT350/500 / More electrical questions
« on: June 14, 2021, 08:25:40 AM »
Yes I have the manual and schematics, just can't figure this one out.
Found these 2 wires, appeared to be cut, maybe the same wire, maybe 2 different ones? Both green, no tracer.
One , I know, goes down to the console harness 4 plug connector- its the one on the right in the pic
The other one (or other end) I cannot figure out
Any help/suggestion is appreciated :)
Thanks, Steve

BTW 69 500 4-spd, non-air

11
1969-1970 Shelby GT350/500 / Fog lights harness routing
« on: June 07, 2021, 03:17:17 PM »
Hey, can someone post a couple of pics of the routing for the fog light harness from firewall to lights?  I'm waiting for the electrical manual and supplement to come in and just wanted to see how this thing was run.

Thanks for any help !!
Steve

12
1969-1970 Shelby GT350/500 / Wiring harness help
« on: May 31, 2021, 09:22:55 PM »
Found a wired bundle of wires under the dash of this 69 500 4spd I’m working on . Anyone seen this or know what all this stuff goes to ?

13
SAAC Forum Discussion Area / Anyone know anything about these or who sells them?
« on: May 09, 2021, 09:11:11 AM »
GT40 seats ?  Wonder who makes these ?

14
SAAC Forum Discussion Area / wiring help
« on: May 02, 2021, 06:56:25 PM »
Ok... I think I f-ed up. Replacing the turn signal switch, tilt 68, and I guess I misplaced a wire. No parking lights, turn signals ...unless the emergency flasher switch is pulled out. This is a new NOS switch.
Anyone have the schematic for the plug, or a drawing , with wire colors and positions ?
Thanks !!

15
1969-1970 Shelby GT350/500 / 1969 re-assembly
« on: April 22, 2021, 07:04:35 PM »
I'm helping a friend reassemble a 69 FB . It was purchased painted and rolling  with a bunch of boxes of parts.
I see a hole in each outer wheelhouse .... brake cooling ducts?
Also  found 2 pieces - fiberglass with similar holes in them ... related to above ?
He may have to buy assembly manuals.. Shelby specific
One more... wat type of rivets for vin tag on dash and Shelby plate on apron .. steel ?


Thanks for any help !
Steve

Pages: [1] 2 3