SAAC Forum

Is there a special signal flasher for the 68 Shelby`s using the dynamite sticks. Any body have part number ?

  Question did the 67 -68 Shelbys ever have a  cobra w/Shelby in small letters on the upper left hand side  of the trunk lid?

Looking for a set Shelby GT 500 big block motor mounts any help would be appreciated .

 
     I`am doing a survey of how many 06` Hertz cars have signature on the underneath frame rails or under members .  It appears that a D.Maze that was the inspector of the Shelby builds for Hertz .signed the rails near the cats & also some Shelby employees also left initials or signatures.    The story is that when Hertz & Shelby found out about it, they put an end to it . I`am not so sure I believe that story . What I do know is my  06 # 0159 has D.Maze on the right rail,  a HLT in faint pen on the left rail & an initial BC on bottom of the cross member.  I have reached out to the Shelby 2006 -2008 Gt & H club & have a few confirmed cars with signatures, with highest number being   0231. Any help with this would be appreciated .

                                                                                              Thanks
                                                                                                 Jim

 
Anyone know what the aluminum tag under the coil  tells us  for example 428- B - 7D  second line ,424-B    ?

   
   Looking for some help on this walnut shift knob with a cobra snake on it. A guy is bugging me about selling it to him but I have no Idea what its worth. I do know its on page two of the ` 60 s Shelby catalogue.

Any idea what new valve covers go for a 66 Gt 350 , these are Ford valve covers in original boxes I guess over the counter Ford product . 

 
  Looking to buy a set of KR rims not sure what the going rate would be. I know they are not produced any more , any ideas what they go for?
  Thanks

    I have a clunging noise in the left side  & believe it is the lower strut rod. I can move both strut rods up and down but the left is easier . Anyone replace these & the  kit I have has two bushings & and washers with a sleeve . Any help would be appreciated.
             

  Is there much difference in original valve covers than the after market ones & what would be a fair price for a set of originals?

I recently changed my rubber bushings just because they were cracking around the  outside edge not because they were worn. I also changed the stabilizer pins. I took the car out & now have a clung when I hit a bump & it seems to be on the driver side.  What I noticed is the drivers side pin is not straight up& down like the passenger pin , not sure why . Any thoughts on this?? Bushings seem okay on the bar.

Two 9,000 r.p.m G.t 350 Tachometers   -one O.E.M  & one later repo U.S made which is brand new great quality tach.. $600 for the OEM & $450 for repo have photos of both if interested

Anyone know of a supplier that sells bullet type wire connectors that fit the Ford connectors (male & female )??

 Just need some idea of what a new set of O.EM valve covers would cost now a days   ?

Did all 68 `s come with a drain pug in the bottom of the tank or maybe mine is not an original ?

 Anyone know the proper output of the voltage regulator ? Mine registers  15.24  V to 15 .4 V just wonder if that is normal.

  Is the serial number of the car stamped on the transmission?

Who would have the number of 67  GT 350 A/c cars that came from the factory

 Looking to find out the width of the OEM  bushing bracket having problems installing polly bushing I believe they are to wide. Any help would be appreciated.

Looking for some help on a tach that person has for sale  . Its chrome case 9 k rpm tach & inside has E-357 stamped on it in ink claims he bought in 1966 for $60  at a Ford dealer. I take it it must be an over the counter tach . Second question what would it be worth to purchase he claims it works fine?
Any help would be appreciated