Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Doog 427

Pages: [1]
1
CSX1000, 4000, 7000, 8000 / CSX 4242
« on: August 28, 2023, 01:12:42 PM »
Hi hope you are well

Looking for history or background on CSX 4242 please

Thank you
Steve

2
1967 Shelby GT350/500 / repop Magstars
« on: June 07, 2021, 10:31:19 AM »
Hi    hope everyone is well

I may buy some newer Magstars, best price I think is CJ Pony Parts $179.00 each, are these any good? Do they last? is chrome finish durable

https://www.cjponyparts.com/legendary-wheel-co-shelby-magstar-alloy-wheel-15-x7-black-machined-1965-1973/p/W121-V/?gclid=Cj0KCQjwvr6EBhDOARIsAPpqUPElLTmypLWtzryZehI5tPFyot3L64UTtS0W1LxAOKvMuG_LXR_9UWQaAq5-EALw_wcB#228=2582


TY
Steve

3
1967 Shelby GT350/500 / rad cap overflow at high 4,000 rpm on hwy
« on: May 31, 2021, 09:52:48 PM »
Hello Hope all are well

Having trouble with rad cap overflow at high 4,000 rpm or higher revs on highway even for short spurt, changed stock cap from 12 lb to 18 lb now have 25 lb, still so much water pressure cap releases and rad fluid blows out drain hose near bottom of car but makes a mess. Ideas?

Thank you
Steve

4
Wanted to Buy / 67 Shelby 2 used 15 x 7 inch Magstars
« on: May 12, 2021, 09:42:55 AM »
Hi

I'm looking for 2 used 15 x 7 inch Magstars for 67 Shelby, could buy 2 new one's, but car has marked up used rims already, so even old aftermarket is appreciated, don't have to be original.

Thank you
Steve
Toronto
1 800 611 0311

5
Wanted to Buy / used 15 inch Magstar
« on: May 06, 2021, 05:40:17 PM »
Hi

I'm looking for 2 used 15 x 7 inch Magstars for 67 Shelby, could buy 2 new one's, but car has marked up used rims already, so even old aftermarket is appreciated, don't have to be original.

Thank you
Steve
Toronto

6
1967 Shelby GT350/500 / 15 inch verse 14 inch
« on: May 04, 2021, 05:41:48 PM »
Hi   hope everyone is well

I want to drive a 67 Gt 500 for small distance 5 miles have Kelsey Hayes front disk, usually have 15 inch rims put set 14 inch on temporarily they spin free and don't rub, clear the break caliper but it is very close, 1/2 inch clearance, anyone done this? Is this a mistake to drive this way?

TY
Steve


7
1967 Shelby GT350/500 / power brakes
« on: March 29, 2020, 02:25:28 PM »
Hi

Have 67 big block with manual brakes rear drum front disk, how much better would power brakes be? noticeable or very much better noticeable? Will car stop in shorter distance

TY
Steve

8
1967 Shelby GT350/500 / Add Power brakes 67 500
« on: August 02, 2018, 05:14:20 PM »
Hi
I have a manual steering 67 Shelby with 488 stroker and very little vacuum,9-10lbs, still have manual brakes any suggestions? Booster etc Do I need to pull motor to install power brake booster? what about Boosta pump noise?

Thank you
Steve

9
1967 Shelby GT350/500 / Horn not working
« on: July 15, 2018, 02:42:08 PM »
Hi
GT500 Horn does not work, ran wire directly from horn to battery and both horns work that way, took off horn button and connected wires and horn is very quiet, barely comes on, ideas?

Steve

10
1967 Shelby GT350/500 / turn signals not working
« on: July 01, 2018, 03:12:38 PM »
Hi
4 way flasher works all lights function, installed new turn signal switch in steering column 1 year ago but since then they stopped, is there a flasher somewhere? Other ideas?
Thank  you
Steve

11
1967 Shelby GT350/500 / car stalls when light on
« on: June 25, 2018, 11:03:25 PM »
Hi
Driving with high beam lights on for 10-15 minutes they flicker and eventually lights go out, tonight driving low beams 10-15 m lights went out and then little later motor just stopped, only way get home is to turn off lights. Ideas?

TY
Steve

12
1967 Shelby GT350/500 / Car 344 former drag car
« on: March 25, 2018, 03:01:36 PM »
Hello, article attached by Rick Kopec from a few years ago about car #344 with a Gas Ronda connection, had engine trouble so we just re built the motor, enjoy , ..Steve

Pages: [1]