SAAC Forum

I'm wondering whats correct for a 1967 Shelby or mustang? from the dealers

  I need to know the opening width on 1967 mustang fastback trunk from inner edge to inner edge of tail light metal I get 15 inches. I know this not a Shelby.
Thank you Jess

I need to know the opening width on 1967 mustang fastback trunk from inner edge to inner edge of tail light metal I get 15 inches
Thank you Jess

HI, Did the GT350's use a cooler for power steering,  motor oil? if so could use a photo or 2 on hose routing.
Thanks, jess

What style is correct for my 67 GT350  build? the Oval  or the pricey  Hipo round air filter? Trying to make it look correct
Thanks

I working on my clone and I'm using a ford mini starter.I don't like the idea having it hot all the time.Question is do people fuse this and  what type?  How to wire using harness to dash?
Thank you

I'm going to do my Amp meter wiring. But I'm using the ford mini starter with the solenoid for it.  I also have the after market amp lug holder on firewall (Branda item )
How to connect wiring to it?

Hi,
I'm working on my 67 replica and I  need a measurement on the back section of "H" pipe center to center= trying to set transverse muffler as this would help, Oh I forgot pipe is 2 1/4
Thank you,
Jess

HI,
I building my 67 289, Should I use a original 3 core Radiator or use a newer Alum. Type? I would like to keep a fan shroud and I'm using a Hipo Fan.
Thanks,
Jess

Hi,
I'm work on my 67 and I have a problem. It has factory Disc KH hays calipers. It seems like my hoses are to short to reach frame mount I did the arning drop and the car is on  jack stands. Hoses measure 15 inches long. Any Idea's whats going on and how to correct?

I'm working on a 1967 fastback and it has the tilt-away column and the  Midland brake booster. What brake line do I use the one that goes over Column or under it? for across the firewall.  There is  2  styles.The car has stock disk brakes.
Need some help here  as no brake line was with car.
Jess

I'm here in California and I have not had any trouble with our gas and older carbs. I plan to be moving to Tn. in a few years. Is there anything I should do because I have heard horror stories about Ethanol and Old carbs. and fuel lines don't hold up well.
Any advice?
Thanks
Jess

I'm building a 1967  Gt350" Clone" not to pass it off as real one. This will NOT be a half A@@ clone !
I have the Branda Roll bar for it  What bolts are used to mount to roof inner side thru ears on roll bar? I have  2 bolts that look like seat belt mounting bolts but smaller in Dia. and longer with same style of bolt head. also ideas on a "nut plate for inside roof  structure .
Thanks, Jess

I'm getting ready to add my export brace to  my car. Question is I see  a weld in support on top where  export brace sits.Is there a plate on the underside to make mounting like a sandwich  style stiffening ?
Thanks
Jess

Hi,
I'm looking for a nice original Export brace to fit a 1967 mustang
Thanks
Jess

Hi,
I'm building my 67 "Clone" and I have the Branda front sway bar (was going to paint it black). I have  the chance to pick up a Stock 67 Bar almost 1 inch in Dia. for the unheard of price of 50.00  (with brackets). what bar fits better and works the best?
The stock bar is LONG gone 
Thanks,
Jess

I'm wondering what most of you use to help  ease up on blind spots.I have a 67 fastback and thinking on a Wink Mirror or a Plano.. along with a right side mirror
Going to use it on the street so ideas are welcome.
Jess

Hi,
I have a oval air filter Assy.  with studs at both ends coming thru lid. I need the bracket to hold this on the carburetor.
What do I do?
Thanks,
Jess

Hi,
I'm in So. Cal and would like to go  to this event for ( Shelby clone no where even close to being done) example on Sat.  is there a spectator entrance fee?

On the old site there was a video of shelby's starting up and taking off there is on part where a man jumps when car is started.
Anyone have a link to that video?
Thanks,
Jess