Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Dan353

Pages: [1] 2 3 ... 7
1
1969-1970 Shelby GT350/500 / 1969 GT350 Z bar clutch linkage adjustments
« on: August 09, 2020, 05:50:33 PM »
Im not sure if my Z bar is bent.   Does anyone know if someone makes a stronger Z bar or a way to reinforce one so it doesnít bend?  I have to almost push the pedal through the floor to get the clutch to engage so I can shift into gear. I used the procedure in the shop manual but my pedal always has to be pushed all the way to the floor to shift.  Is there a way to adjust the lower rod to make it disengage closer to the top of the pedal travel and still have enough free play?  Also I installed a Center force clutch and pressure plate and throw out bearing and cannot get the pedal to come all the way up without assistance. I had to put a heavier spring to the Z bar from the firewall in order to get the pedal to come full up.    Thanks in advance for any help you can give
Dan

2
Thank you for the information

3
  Iím no expert so educate me.  How about posting some references,articles,videos etc... so that I may get a better understanding

Dan

4
It seems what is called a proportioning valve might do both proportioning and act as a residual valve.   Check out this video  yes I know heís talking about mopars but he does Ford brake parts too

https://youtu.be/qzUk8W1-2pw

5
Found this distribution block and proportioning valve (residual valve) all in one. From NPD  their part number is 2B091-20AA says it fits 1964-1971 FAIRLANE FAIRLANE, TORINO, 70 1/2 FALCON.

6
Well if your going to be like that. why does the 1969 shop manual call it a proportioning valve?  maybe on the earlier years they used a residual valve but clearly in 1969 they used a proportioning valve. See photoís taken of 1969 shop manual for Cougar and Mustang.

7
Your going to need a proportioning valve also to balance the front and rear.  Discs use a different amount of fluid compare to drum brakes.  You can try Macís for a stock parts or you can use an adjustable proportion valve from an after market brake supplier like Bear brakes

Dan

https://www.macsautoparts.com/

https://baer.com/

8
Correct me if Iím wrong  but that looks to be a drum brake distribution block (drum brakes at all four wheels).  Do you have a proportioning valve installed for the rear brakes?  These pictures are for a 1969 Mustang Sorry about the pictures can never get them to come out right

9
1969-1970 Shelby GT350/500 / Re: Hood screens
« on: July 23, 2020, 10:49:58 AM »
I just wanted to say thank you to everyone for the information

Dan

10
1969-1970 Shelby GT350/500 / Re: Hood screens
« on: July 21, 2020, 08:17:04 PM »
 Sorry but I donít know what a Ted bonding agent is or what FRP stands for.  Is there a place to purchase these materials?  Or what else can be used to secure the screens

11
1969-1970 Shelby GT350/500 / Re: Hood screens
« on: July 19, 2020, 06:22:21 PM »
Thank you for the information Bob who ever installed my front screens used silicone.  What material was used to glue in the back screens?
Dan

12
1969-1970 Shelby GT350/500 / Re: Hood screens
« on: July 19, 2020, 01:51:33 PM »
Jeff,  thank you for the pictures.  My car was built January 6 1969  I donít know when it was converted to a Shelby GT350.  Iím guessing from the pictures that the rear screens are glue only and the fronts are glued and have the two fasteners.  The screens on my car look like the pictures but are loose (one forward and one of the rears has half the glue missing) and need to be secured.  Is there any special tricks to installing them? It looks pretty straight forward. Thanks again for your help.
Thank you    Dan
 

13
1969-1970 Shelby GT350/500 / Hood screens
« on: July 18, 2020, 06:27:48 PM »
Does anyone know how the  screens where originally attached to the hood were they glued or screwed on?   If you would please post pictures.   Thank you
Dan

14
News from HQ / Re: So... what do we call it next year?
« on: July 03, 2020, 09:59:00 AM »
Call the first day SAAC 45 and name the following days SAAC 46 than you could keep the numbers. Lol.   Or have  SAAC 45 in December. Used to have the  show in Vegas. Call it SAAC 45

15
SAAC-45 / Re: SAAC-45 Convention Update
« on: July 01, 2020, 07:36:10 PM »


     Autobahn

Pages: [1] 2 3 ... 7