Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 67gt500

Pages: [1] 2 3
1
He does say it’s a Repo in the description.. Maybe he took your advice..

2
1967 Shelby GT350/500 / Re: Pertronix 3 wiring?
« on: April 21, 2020, 12:48:27 AM »
OK, so the 2 Tach wires are the Red / Green stripe that loops from the ign switch and has a female connector and the Pink / Red has the bullet connector.. This is the one you use to splice into for the 12V feed ?

(just noticed the terminal popped out of the Ign Switch block)

3
1967 Shelby GT350/500 / Re: Pertronix 3 wiring?
« on: April 20, 2020, 08:52:33 PM »
I had a old loom around, so I did a mock up of how or where to splice the new 12 V wire that runs out to the Pertronix.. Splice is done on the red / green stripe wire..
“The going thing” is this how you did yours ?

4
Shelby American History / Re: Marchal lights on Shelby's
« on: September 20, 2019, 05:18:16 PM »
I still have a set of those that I picked up at a swap meet 30 years ago.. I never did find out where or what they fitted.. but they looked cool sitting on the shelf in the cave..
Hope you can find out more about them..

5
1967 Shelby GT350/500 / Re: Friendly warning
« on: August 02, 2019, 05:09:25 PM »
Here is his email address

captcj@hughes.net

6
1967 Shelby GT350/500 / Re: Friendly warning
« on: August 01, 2019, 05:51:15 PM »
Hi Randy, yep your right with supply issues, and I total understand that, that was his issue with the pistons, but I had to chase him for information, which was like playing detective across different forums until I got a response.. Wouldn’t answer via his company emails. I would even ring his business phone number and it would just go to answer phone, on multiple occasions.. Then the stories would not align.. and I was prepared to hang in there and wait for the parts, but man,it just became “ shit I’m going to lose my coin here” if I don’t do something. So I asked for it back, and then that became a drawn out process.. and that’s the short version of events..
I ended up getting what I needed from Blair Patrick.. Now, there is a top bloke to do business with..

7
1967 Shelby GT350/500 / Re: Friendly warning
« on: August 01, 2019, 03:45:40 AM »
6972Boss, i had the same problem, but with a FE stroker kit, brought through his web site.. paid the coin and then nothing.. what a drama..
Your story sounded exactly what happened to me.. All sorts of excuses.. 1 year later i finally got my money back.. Never again.. Put my engine build back 2 years. I'm sure there is going to be some folks who say, "he was great to deal with", but i'm with you.. tread carefully..

8
1967 Shelby GT350/500 / Re: Tachometer Wiring Upgrade
« on: July 30, 2019, 04:17:46 PM »
How about just posting the “How to do this” for all to see ?

9
Parts For Sale / Re: For Sale: FE Parts
« on: May 22, 2019, 04:49:33 AM »
PM sent

10

Make sure the headers you buy will fit with the original z-bar clutch components. The FPA tri-ys don't. You need a hydraulic clutch with those.
[/quote]

ShelbyDoug, i run the FPA tri-ys with the original z-bar components.. You do have to trim the bottom off the bracket that is bolted to the block, so it fits flush with the block.. but no need for a hydraulic setup..

11
The Lounge / Re: Cam question for a stroker FE
« on: February 15, 2019, 12:46:04 AM »
Go one better and contact Blair Patrick.. He will give you great cam information and his service is very good..    captcj@hughes.net

12
Wanted to Buy / Re: 67 GT500 Front Carb Linkage
« on: January 20, 2019, 01:49:22 PM »
The thing is I don't need the whole set up.. Some where a long the way, the front linkage was replaced with a incorrect one.. Really just looking for that part or a set of linkage rods..

13
Wanted to Buy / 67 GT500 Front Carb Linkage
« on: January 19, 2019, 03:24:29 PM »
Hi, looking for a front carb linkage.. this is the shorter of the 2 linkage’s.. I would take both linkages, if require as a set.. they have to be original.. Thanks

14
The Lounge / Re: DeChroming advice? Anyone?
« on: December 06, 2018, 02:09:36 PM »
I did a chrome export brace a number of years ago.. I am sure a just sanded it and then I sprayed it with a Wurth product.. Then over sprayed that with a semi gloss black.. worked a treat.. I will see if I still have the Wurth can on my self..

15
1967 Shelby GT350/500 / Re: Center headlight bracket style
« on: November 28, 2018, 02:48:41 AM »
#486 - 3 hole - SA completion 1/31/67

Pages: [1] 2 3