Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - PR

Pages: [1] 2 3 ... 6
1
I think Pete is right, my 70 Mach 1 351 car has a black spring, not green,green= big block I would imagine

2
Ok, that is a 70, brake pedel bolt center line to center of brake pin is 5 1/2", 69's are 6", clutch pedel should be the same, if the spring tension is different I don't think it will affect functionality ,green/ black makes no difference to me,once installed I won't be looking at it

3
I never heard that before Pete, 351w, SB, they go through the same firewall hole, can't be that different

4
Yes, have everything else,

5
Wanted to Buy / WTB 69 clutch pedal w/spring and bracket to support
« on: April 03, 2020, 02:35:40 PM »
Let me know what you have, looking for ford parts, thanks
Rudo9@comcast.net

6
SAAC Forum Discussion Area / Re: Bellhousing interchange 302-351
« on: April 01, 2020, 09:46:31 AM »
Thanks, that is what I thought, I have a 164 tooth bellhousing, I will buy a 28oz  flywheel for 11" clutch, I am converting a 69 mach 1 automatic to a 4spd , will the automatic starter work with the 4spd, like the FE, or are there 2 different starters, thanks again

7
SAAC Forum Discussion Area / Bellhousing interchange 302-351
« on: March 31, 2020, 11:20:28 AM »
Will a 302 4spd bellhousing work on a 351 w or is 351 specific

8
1968 Shelby GT350/500/500KR / Drive shaft length chart
« on: March 19, 2020, 01:04:38 PM »
Mustangtek use to have a chart on drive shaft length, but I can't locate it now, does any one have it to share, I need a new one built for a new project, thanks Pete

9
1966 Shelby GT350/GT350H / Re: How many on this site have a red Hertz?
« on: February 16, 2020, 08:42:04 PM »
There was one I seen in a garage in Santa Rosa ca, red, gold stripes auto, he said it was a hertz car, very original, but engine had issues that's why it was parked and why this guy got the car

10
Wanted to Buy / Re: Small block dual quad intake
« on: February 09, 2020, 11:43:51 AM »
I have a setup rudo9@comcast.net

11
Wanted to Buy / Re: 68 GT500 Fan Shroud
« on: January 22, 2020, 10:33:12 AM »
There is an nos one on the 428 cobra jet forum 1100.

12
1968 Shelby GT350/500/500KR / Re: Export brace question
« on: December 28, 2019, 09:50:54 AM »
Thanks Bob

13
1968 Shelby GT350/500/500KR / Export brace question
« on: December 27, 2019, 10:50:52 AM »
I need an export brace for one of my mustangs and I have seen junk that doesn't look like the ford one on my Shelby, stamping was different, who makes a good repo that fits and looks like an original

14
1968 Shelby GT350/500/500KR / Re: '68 KR - Clutch
« on: October 29, 2019, 10:24:08 AM »
You can get the ram clutch from Brent Lynkens Motorsport, ram power grip HD, I have used them on 2 ,427 street cars and a CJ mustang, if you're hard on clutches this one can take a beating and lasts

15
Wanted to Buy / Re: '67 HiPo Connecting Road
« on: October 27, 2019, 01:38:52 PM »
I have a nos one, send email to rudo9@comcast.net and I can send pictures
I believe mine is pressed pin, no squirt oil hole on small end

Pages: [1] 2 3 ... 6