Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Doog 427

Pages: [1] 2 3
1
CSX1000, 4000, 7000, 8000 / CSX 4242
« on: August 28, 2023, 01:12:42 PM »
Hi hope you are well

Looking for history or background on CSX 4242 please

Thank you
Steve

2
1967 Shelby GT350/500 / Re: repop Magstars
« on: June 09, 2021, 06:57:39 PM »
Hi Dave

I would love an old set Magstars can you connect me? e-mail also sent

TY
Steve
1 800 611 0311  ext #1

3
1967 Shelby GT350/500 / Re: repop Magstars
« on: June 09, 2021, 05:56:05 PM »
Hi

I understand the Paradise Wheel 1967 Magstar is much better don't have reply from them yet, web site says customs order, could be a while to get them and $450.00 each x 2 = $900.00. I wanted opinion if I order the legendary Magstars yes they are aluminum but could get 4 for $800.00 and would all look same, thoughts?

TY
Steve

4
1967 Shelby GT350/500 / Re: rad cap overflow at high 4,000 rpm on hwy
« on: June 09, 2021, 10:08:33 AM »
Hi Everyone, appreciate feedback on rad cap overflow

Motor and water pump new did test for bubbles and head gasket anyway, was OK, I took the easiest route first, lowered the fluid level more than usual, to barely above fins, also put a small overflow container on end hose off rad cap if it pukes would catch it and then maybe suck fluid back in when cool, switched higher pressure rad cap, added water wetter and so far seems OK, car runs cool

Thank you
Steve

5
Wanted to Buy / Re: used 15 inch Magstar
« on: June 08, 2021, 06:39:52 PM »
Hi   hope everyone is Ok

Still need 2 used Magstars, love to finish my car, any news appreciated

Steve
1 800 611 0311
ext #1

6
1967 Shelby GT350/500 / Re: repop Magstars
« on: June 07, 2021, 07:45:02 PM »
Hi

OK very good feedback appreciate it, will not get CJ ones, Looked at Paradise Wheels see how long takes to get 2 of them. Would prefer 2 used ones have another post on "parts wanted" but none found so far

TY
Steve
1 800 611 031 ext #1
Home office

7
1967 Shelby GT350/500 / repop Magstars
« on: June 07, 2021, 10:31:19 AM »
Hi    hope everyone is well

I may buy some newer Magstars, best price I think is CJ Pony Parts $179.00 each, are these any good? Do they last? is chrome finish durable

https://www.cjponyparts.com/legendary-wheel-co-shelby-magstar-alloy-wheel-15-x7-black-machined-1965-1973/p/W121-V/?gclid=Cj0KCQjwvr6EBhDOARIsAPpqUPElLTmypLWtzryZehI5tPFyot3L64UTtS0W1LxAOKvMuG_LXR_9UWQaAq5-EALw_wcB#228=2582


TY
Steve

8
1967 Shelby GT350/500 / Re: rad cap overflow at high 4,000 rpm on hwy
« on: June 01, 2021, 05:15:37 PM »
Ok thank you many replies let me check into this appreciate it

9
1967 Shelby GT350/500 / rad cap overflow at high 4,000 rpm on hwy
« on: May 31, 2021, 09:52:48 PM »
Hello Hope all are well

Having trouble with rad cap overflow at high 4,000 rpm or higher revs on highway even for short spurt, changed stock cap from 12 lb to 18 lb now have 25 lb, still so much water pressure cap releases and rad fluid blows out drain hose near bottom of car but makes a mess. Ideas?

Thank you
Steve

10
1967 Shelby GT350/500 / Re: 67 photos from the web
« on: May 18, 2021, 06:56:29 PM »
Amazing same home town as Bill, He purchased the car in the spring of 1967 through Cady & Pier dealership in Sandpoint, Idaho.  He drove on street 67 raced the 428 in 68 then, yes He put a 427 in car and drag raced it and ran pretty well. Do you know Bill now?

No, I am from Spokane, where McCollum Ford, the authorized dealer that sent #344 to Cady & Pier. I now live on the other side of the state.

But I was just in Sandpoint last weekend as I am looking to relocate to the area. Is Bill still around?

Hi 2112 sorry for delay yes Bill is still around  now we met many years ago and he got to drive his car again after over 30 years

Doog427 are you the current owner of #344?
Yes 2112 current owner for past 33years

11
Wanted to Buy / Re: used 15 inch Magstar
« on: May 18, 2021, 03:54:29 PM »
Hi

If I cant find used Magstars what is best place to get re pops?

Thank you
Steve

12
1967 Shelby GT350/500 / Re: 67 photos from the web
« on: May 16, 2021, 07:00:48 PM »
Amazing same home town as Bill, He purchased the car in the spring of 1967 through Cady & Pier dealership in Sandpoint, Idaho.  He drove on street 67 raced the 428 in 68 then, yes He put a 427 in car and drag raced it and ran pretty well. Do you know Bill now?

No, I am from Spokane, where McCollum Ford, the authorized dealer that sent #344 to Cady & Pier. I now live on the other side of the state.

But I was just in Sandpoint last weekend as I am looking to relocate to the area. Is Bill still around?

Hi 2112 sorry for delay yes Bill is still around  now we met many years ago and he got to drive his car again after over 30 years

13
Wanted to Buy / Re: used 15 inch Magstar
« on: May 13, 2021, 02:04:34 PM »
Hi mtdubvee tried to PM didn't work?   Hope you are well

Yes if you have 15 x 7 Magstar may want one can you e-mail picture front and back? Perhaps price you may want?

Steve
todayshousewares@cogeco.ca

14
Wanted to Buy / 67 Shelby 2 used 15 x 7 inch Magstars
« on: May 12, 2021, 09:42:55 AM »
Hi

I'm looking for 2 used 15 x 7 inch Magstars for 67 Shelby, could buy 2 new one's, but car has marked up used rims already, so even old aftermarket is appreciated, don't have to be original.

Thank you
Steve
Toronto
1 800 611 0311

15
1967 Shelby GT350/500 / Re: 67 photos from the web
« on: May 07, 2021, 03:24:27 PM »
Amazing same home town as Bill, He purchased the car in the spring of 1967 through Cady & Pier dealership in Sandpoint, Idaho.  He drove on street 67 raced the 428 in 68 then, yes He put a 427 in car and drag raced it and ran pretty well. Do you know Bill now?

Pages: [1] 2 3