Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - FordGT

Pages: [1] 2
1
1967 Shelby GT350/500 / Re: Spec Rear End Question?
« on: January 09, 2020, 07:18:22 PM »
Thanks Guys....

2
1967 Shelby GT350/500 / Spec Rear End Question?
« on: January 08, 2020, 09:52:53 PM »
Does anyone know what yoke Ford used with the SPEC rear end case?  1310, 1330 or 1350

Thanks

3
I'm also still scratching my head on #2?

4
Anyone know of any tricks on removing frozen studs out of the aluminum tail light frames?  Some of the studs are broken off already just above the face of the frames.

Thanks

5
Wanted to Buy / WTB: 67' GT350 Shelby Parts...
« on: December 20, 2019, 08:40:06 PM »
Looking for the following 67' GT350 parts:

1 - C7ZE 289 HiPo head, non-Smog with built date Dec. 1966 (6M)
1 - C7ZA 289 NOS Motor mount
Passenger Side curved grill mounting bracket
Early Steel inner tail light mounting plates
NOS rear quarter panel end caps
Holley Carbs,  C6OA-A or C6OA-B

Have cash or many other 67' for trade,,,,  Thanks

6
Wanted to Buy / WTB: 67' GT350 Shelby Parts...
« on: November 07, 2019, 07:31:00 PM »
Looking for the following 67' parts......

289 C7ZE HiPo Head, prefer non-smog
Early tail light aluminum frame without screws holes
NOS, Quarter panel end caps
RT front hood pin mounting bracket
Underdash aluminum gauge pod and wiring
Paxton Cobra Carb Air Box

Have cash or other parts for possible trade.....  Please send me PM...

Thanks

7
Wanted to Buy / Re: WTB: 67'Parts...
« on: September 11, 2019, 09:33:16 PM »
Bob, looking for the frames without the screw holes.

Thanks

8
Wanted to Buy / WTB: 67'Parts...
« on: September 09, 2019, 11:05:38 PM »
Looking for the following parts:

1- C7ZE 289 HiPo head
Aluminum tail light trim frames
NOS- Quarter Panel End Caps
Tail light inner truck metal mounting brackets

Thanks and please send me PM....

9
1967 Shelby GT350/500 / 1967 GT350 Engine ?
« on: April 06, 2019, 08:38:48 PM »
Anyone have any kind of idea what an original GT350 289 Hipo engine would be worth, Air cleaner to oil pan all date coded Dec. of 1966.  Engine is taken apart but all original/ complete and still  standard bore.  What would the Rug-N trans with shifter also be worth?

Thanks

10
Wanted to Buy / Wanted - C7ZE 289 HiPo Head
« on: March 31, 2019, 07:26:45 PM »
Looking for 289 HiPo head C7ZE Non Smog

Thanks

11
1967 Shelby GT350/500 / Inboard Headlight Question?
« on: December 27, 2018, 12:42:01 AM »
What are the correct fasteners for inboard headlight buckets?

I own an early February GT350 and the car does have inboard lights. My lights have 3/16 x 1/2 hex bolts with lock washers.  Are these the correct fasteners? or is slotted sheet metal screws correct?

Thanks

12
Wanted to Buy / WTB: Ford 289 2x4 Carter Carbs......
« on: December 16, 2018, 09:11:14 PM »
Looking for the Carter carbs that was sold over the counter on the 289 2X4 Cobra Intake setup by Ford.

Think, correct carbs are Carter's 3258s and 3259S stamped on the right front mounting flanges.  Also, looking for fuel log, chrome air cleaners and linkage..

If anyone has any of these parts or single carb, please send me PM trying to put a setup together for my car. 

I only have the intake @ this point...

Thanks

13
Wanted to Buy / WTB: 1967 Shelby Parts....
« on: December 09, 2018, 07:18:13 PM »
Looking for the following 67' parts....

 - Passenger side hood pin mounting bracket
 -  Aluminum Tail Light Trim Ring, early style with screw in studs
 - Tail Light Inner steel mounting brackets
- NOS fiberglass quarter panel end caps

Also looking for 1- C7ZE 289 HiPo head in good shape, non-smog..

Thanks, please send me PM....

14
Wanted to Buy / Ford 289 2x4 Holley Carbs......
« on: December 01, 2018, 02:54:06 PM »
Looking for the Ford 289 2x4 Holley carbs.  C6OA-A -List 3360 or C6OA-B - List 3361....  Needed a pair or I would also be interested in either one carb singly......


Please send me PM,  Thanks

15
Wanted to Buy / Wanted: C7ZE 289 Hipo Head
« on: September 03, 2018, 07:01:29 PM »
Looking for 1 or a pair of C7ZE 289 HiPo heads.

Please send me PM,,,  Thanks

Pages: [1] 2