Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - nwfire

Pages: [1]
1
1967 Shelby GT350/500 / sound deadening material / door panels
« on: April 12, 2022, 12:26:38 PM »
So, #906 is going in for new paint next month.  While this won't be a concourse restoration, I would like to make it as factory correct as I can.  I'm looking for replacement insulation/sound deadening material for around the rear fender wells, and the upper and lower air scoop area.  Currently I can't find any material to match some of the original material still on the car.  Anyone have suggestions as to where to find this material?  Also, I'd like to replace my Deluxe door panels with the brushed aluminum inserts as the ones on the car now are hard as rocks and don't lay flat on the doors.  Anyone have suggestions here also as to who has a quality door panel that fits well?
Thanks for your help.

2
1967 Shelby GT350/500 / One piece fuel line, GT500
« on: February 12, 2022, 07:37:31 PM »
Can anyone recommend a one piece fuel line for the 67 GT500 that actually fits without making a bunch of changes to it?  Purchased one from NPD and although it says it's for the GT500, it's quite different than the one I have on it now.  Also, any easy way to thread one of these in place??

Thanks.

3
GT/CS - California Special / Power Steering Fluid
« on: July 25, 2021, 11:47:04 PM »
Can someone tell me what the power steering fluid should be for the 1968 California Special Mustang with 302 engine??
Thanks.

4
1967 Shelby GT350/500 / kick down cable adjustment
« on: January 13, 2021, 10:49:47 PM »
Can anyone help with explaining the proper procedure for adjusting the kick down cable on a 1967 GT500 with a C6 automatic transmission??

Thanks.

Terry Hill
1967 GT500, #906


5
1967 Shelby GT350/500 / GT500 carb heater tube
« on: March 18, 2020, 01:32:15 PM »
Putting the dual quads back on my GT500.  Where does the carb heater tube go on the passengers side of the engine and is this a two piece heater tube connected together by a flex/vaccum type hose?  Anyone have pictures where it is affixed on the engine/exhaust on the passenger side??
Thanks.

6
1967 Shelby GT350/500 / intake manifold oil filler cap
« on: March 13, 2020, 03:14:38 PM »
Anyone know of a vendor where I can purchase a correct oil filler/breather cap for my 1967 GT500?  This is the tube at the front of the intake manifold on the passenger side.  Need the push in style of cap, not the twist style.

Thanks for the help.

7
1967 Shelby GT350/500 / 67 GT500 proper cylinder heads
« on: November 29, 2018, 06:12:20 PM »
OK, I'm looking for some help on proper cylinder heads for my 67 GT500, #906.  Car presently has C8AE heads and headers on it and I'd like to return it more to stock configuration.
I purchased a set of C7AE-A cylinder heads with the 16 bolt pattern and a set of "stock" (as advertised) exhaust manifolds, numbered C60E-9430-A and C70E-9431-A.  The problem is the exhaust manifolds don't fit the 16 bolt pattern on the heads, the upper front bolt hole on the heads are off about 1/2".
I know that there were 8, 14 & 16 bolt configurations, but were the one's used on the PI engines the 14 or 16 bolt configuration??

Thanks for any help.

Pages: [1]