Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - hertz350

Pages: 1 ... 3 4 [5] 6 7 ... 10
61
1966 Shelby GT350/GT350H / PCV Rubber Hose
« on: February 23, 2021, 06:47:34 PM »
Looking to find out the most correct pcv rubber hose to use on a March built '66 Shelby. For example, is it ribbed or alligator finish and what approximate outside diameter is it? According to what I have seen in pictures here and what I have read here, there could be a difference in hoses on the engines assembled at Ford with the hose attached and those cars where the hose was installed at SAI.

Thank you.
   

62
1966 Shelby GT350/GT350H / Re: Tach wiring picture
« on: February 22, 2021, 10:14:10 PM »
I threw the nuts away. I was mistaken in my earlier post to not remember they were standard 3/4" nuts by probably 3/8" height. They were not lug nuts. Maybe a previous owner installed them.

63
1966 Shelby GT350/GT350H / Re: Tach wiring picture
« on: February 22, 2021, 08:27:16 PM »
This brings up a few questions.

Did the original tach come to Shelby with molded on male plugs to plug into the female loom leads? If not, did Shelby solder on or crimp on male connectors?

Was the dash pad removed during the process of installing the tach? If not how did the spacers get placed in to prevent crush of the dash pad on installation of the screws?

Regarding spacers, when I removed my dash pad it had lug nuts used as spacers. Has anyone else had lug nuts used as spacers? I can see Shelby doing that.

64
1966 Shelby GT350/GT350H / Re: Tach wiring picture
« on: February 22, 2021, 06:42:47 PM »
Thanks. Yes I have that from the Concours Mustang Library. I am looking for a picture of the actual wiring connections under the dash. In particular, I want o see how it is connected under the dash to the tach wire or whether it needs a separate wire to the tach?

65
1966 Shelby GT350/GT350H / Tach wiring picture
« on: February 22, 2021, 06:12:20 PM »
I am looking for a picture  and wiring diagram of the wire connections for the Shelby tach for a 66 built in March. I have my original dash wiring loom and it has splices with the original tach wires wire spliced in with crimp on red butt connectors. My tach has been rewired and I want to make sure I get the wiring right and as close to original as possible. My tach has a red, blue and a black wire.

Thanks for the help. 

66
Wanted to Buy / 66 289 NOS Thermostat Housing
« on: February 17, 2021, 05:37:35 PM »
Looking for a NOS thermostat housing for a 1966 289. I thin it is marked C40 and has the cast in groove for the thermostat.


67
Parts For Sale / NOS head gaskets
« on: February 15, 2021, 07:03:29 PM »
2 sets of Ford small block head gaskets. One set is new. One set was test fit but engine was not run.
$70 for all 4. Plus shipping.

68
1966 Shelby GT350/GT350H / Re: getting p.o.ed
« on: February 10, 2021, 05:52:19 PM »
Thanks. I know you meant "on" the engine. I will paint that part blue.

69
1966 Shelby GT350/GT350H / Re: getting p.o.ed
« on: February 10, 2021, 03:30:15 PM »
What color is correct for both parts of the fuel line bracket at the water pump?

Thanks.

70
1965 GT350/R-Model / Re: Rear quarter radio antennas on 65s
« on: February 08, 2021, 04:31:06 PM »
My guess then is that the "rule" would be that all most if not all Hertz cars were to have the radio antenna at the right front fender? Were the antennas for Hertz cars installed at SAI or at the dealer where delivered to before Hertz took possession?

71
Wanted to Buy / Tach wiring sleeve
« on: February 07, 2021, 11:39:06 PM »
Looking to find the material for covering the wires on a 66 Shelby tach. The i.d. of the plastic sleeve or cover is about 3/8". Any suggestions would be appreciated.

72
Still looking for a picture of these.

73
I am looking for a picture or diagram of the Tri Y original header gaskets used at Shelby around March of 66.

I am trying to find a pair of these or good substitute.

74
Wanted to Buy / High Performance Manual
« on: January 21, 2021, 11:32:50 AM »
I am looking for an original High Performance Manual as shown in the picture below of a reproduction one.

75
Concours Talk / Wheel weights on a 66 Hertz car
« on: January 20, 2021, 02:29:21 PM »

Would there be a point deduction in the Concours Trailered class if a Hertz car did not have wheel weights on the Magnum 500 wheels?

Pages: 1 ... 3 4 [5] 6 7 ... 10