Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - SFM6S

Pages: 1 2 [3] 4
31
1967 Shelby GT350/500 / Re: Recent discussion on Morrison's 67 G.T. 500
« on: February 08, 2021, 01:08:13 PM »
And to paraphrase Mojo Nixon....he's in your jeans, he's in your mothers jeans, wait...Mojo is referring to Elvis

32
SAAC Forum Discussion Area / Re: Checkered Flag : Jim Cowles (acman63)
« on: January 06, 2021, 08:52:46 AM »
Jim, RIP; Sharon and Emily, our thoughts and prayers are with you. I first started buying stuff from JC in 1984 and he was helpful and talkative from the first conversation. Uncle Jim always was always able to help or point you in the right direction. The last time I spent time with Jim was at MCACN in 2018 when neither one of us knew the other would be there. We spent most of Saturday afternoon palling around and he introduced me to Bob Perkins and many of his customers that were there. Jim was forever a class act.

Joe Bolis

33
1966 Shelby GT350/GT350H / Re: Rear quarter Window Interior Trim
« on: November 23, 2020, 11:57:04 AM »
I would buy a set and prepay as well.

Joe

34
1965 GT350/R-Model / Re: T10 shift rods and levers
« on: November 17, 2020, 03:04:37 PM »
PM sent.

35
The Lounge / Re: 2020 Annual
« on: November 13, 2020, 08:25:59 AM »
Received mine in the mail yesterday in Denver. A pleasant surprise!

Joe

36
Sorry to read that JC's recovery is slower than expected. Nice to see you stepping in to help Jim.
Best wishes to Jim and his family.

Joe

37
Thorazine?

38
Wanted to Buy / Re: Chuck Cantwell T shirt
« on: August 11, 2020, 04:15:56 PM »
Please count me in for an XL

39
Wanted to Buy / Re: 65 backing plates
« on: May 14, 2020, 05:07:44 PM »
Pm sent.

40
I believe that Jeff is asking because he removed a 427 from his car and is installing the correct 428 PI. He is having issues lining everything up.

Joe

41
The Lounge / Re: The Shelby American 2019 Annual
« on: December 11, 2019, 03:05:58 PM »
Recieved mine yesterday afternoon in CO.  Lots of great stuff!

42
The Lounge / Re: Tool for directional signal pins/plug
« on: March 22, 2019, 10:11:53 AM »
You could also go to you local hobby store and buy a piece of brass tube the correct inside diameter...might be faster than waiting on a tool from a vendor.

Joe

43
The Lounge / Re: Shelby Prices at Auction
« on: March 21, 2019, 10:39:12 AM »
Basketweaving

44
The Lounge / Re: Cannonball Kopec
« on: March 08, 2019, 09:45:21 AM »
It was in an issue after vol 5 number four...I was looking thru all of them recently before I gave them to a local club member.
Seems it was near the front of the magazine.

45
The Lounge / Re: Cannonball Kopec
« on: March 08, 2019, 09:17:06 AM »
shelbydoug,  It was Captain Normal and the pic was done after he had a high speed mishap on a rally; left front fender and wheel incident.

Joe

Pages: 1 2 [3] 4