Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - rcgt350

Pages: 1 2 [3] 4 5
31
I have a picture(printout) of 0023 from a previous owner about 19 years ago, are talking same person then, I currently donít recall that owners name.

32
Wanted to Buy / 67 GT 500 Without Engine
« on: August 26, 2019, 10:23:56 AM »
Looking for a 67 GT500 less the engine, 4 spd preferred and will consider all colours.
Have a 2012 GT500 available for partial trade , it has approximately 400 miles on it, Red/White Stripes.
 Contact : rcsands@northwestel.net

33
1967 Shelby GT350/500 / Re: CAUTION! Car number 67200F7A01377 Indiana
« on: August 24, 2019, 12:18:29 PM »
Did 67í GT 350ís come fr9m the factory with engine lift hooks?

34
1969-1970 Boss 302/429 / Re: Survivor
« on: August 13, 2019, 01:48:50 AM »
So are you up to 6 now Ed still existing? That sounds like an incredible car. Did it appear solid and undusturbed for the most part.

35
1967 Shelby GT350/500 / #0016 Crossing Block in May at Mecum
« on: April 07, 2019, 02:35:48 AM »
#0016 slated for Mecum, May 14-19 in Indianapolis.
Anyone know much about this one?
I see the rad hose clamps could be changed out.

36
1967 Shelby GT350/500 / Re: Paradise Magstar Balancing Recommendations
« on: March 19, 2019, 10:01:27 AM »
I had mine done with the old school system, canít remember what thatís called and glue on weights on inside, not Concours correct, but I didnít want the Chrome rim marked up with outer wheel weights either. No balance problems going down the road.

37
1967 Shelby GT350/500 / Re: Restoring EFFPI steering wheel
« on: March 14, 2019, 12:33:54 AM »
Yes, I believe it was Speciality Wheel. Good people as I recall.

38
1967 Shelby GT350/500 / Re: Restoring EFFPI steering wheel
« on: March 13, 2019, 09:55:05 AM »
There was an outfit in Florida that I sent my wheel to about 18 years ago, they cut the wheel open at two of the spokes to weld them back to the rim, put the wood back in and refinished the entire wheel. Itís been good ever since and you canít tell visually that anything like that was ever done. I just canít remember the name of them? Does anyone here recall them?

39
1966 Shelby GT350/GT350H / Re: I just became the owner of 6S1066
« on: March 12, 2019, 11:19:24 PM »
What about the 964 ?

40
Wanted to Buy / Re: C5AZ-6A666-A PCV Valve
« on: March 05, 2019, 12:56:57 AM »
I saw the ones on EBay, if the price was in real time, the. We wouldnít be looking at those still.
Donít mind paying for something, but I also donít like bending over!
 Iíll look around in dark corners.

41
Wanted to Buy / C5AZ-6A666-A PCV Valve
« on: March 04, 2019, 04:58:40 PM »
Looking for a NOS PCV. Valve, C5AZ-6A666-A
Randy

42
The Lounge / Re: Shelbys, Mustangs and Fords in Movies or TV
« on: March 03, 2019, 09:30:50 AM »
Does anyone know what number the Get Smart Shelby was? Iím assuming it was a real one back then.
 I knew there was a Shelby in one of these shows back then, I kept thinking it was I Dream Of Jennie.
Many years ago!

43
1967 Shelby GT350/500 / Re: 67 sewn trunk mat
« on: February 26, 2019, 10:16:21 AM »
OH may be, I'll check that again.
Thanks

44
1967 Shelby GT350/500 / Re: 67 sewn trunk mat
« on: February 25, 2019, 11:17:51 PM »
So Do both ACC & NPDís Burtex come sewn, ready to install?
Whatís the 17691 part # giving you @ $420.24 ?

45
I didnít know there was so much to this PCV Valve. I currently have a round version on 0031. Is the EV-50 in a Hex version the correct one? C5AZ-6A666-A

Pages: 1 2 [3] 4 5