Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - musclecarman15

Pages: [1] 2 3 ... 11
1
Wanted to Buy / wanted autolite 69 gt350 oil breather cap
« on: March 18, 2024, 10:55:47 AM »
wanted...69 -70gt350 ,original chrome autolite oil breather cap, this is the push on one..thx keith 318-393-1502

2
Wanted to Buy / Re: Carburetor air cleaner stud
« on: February 07, 2024, 11:21:00 AM »
found,thx

3
Wanted to Buy / Re: 16 in anco wiper blade insert
« on: February 04, 2024, 04:32:07 PM »
Found ,thx

4
Wanted to Buy / Carburetor air cleaner stud
« on: February 02, 2024, 03:51:27 PM »
Wanted .. original air cleaner stud for 69 mustang / Shelby(gt350) with 351w  4bbl. Carburetor (autolite 4300).Stud will be 1/4-20 on each end and approximately 4 1/4 in overall length...top part length,where air cleaner wing nut goes is approximately 1 7/16 -1 1/2 above separation nut. Thank you Keith 318-393-1502

5
Wanted to Buy / 16 in anco wiper blade insert
« on: January 28, 2024, 02:34:13 PM »
Looking  for two 16in anco wiper blade inserts,will have 2782444 on the rubber in very small print. Either nos or very nice used. Thx Keith 318-393-1502

6
1969-1970 Shelby GT350/500 / Re: 1969-70 shelby gt350 choke shield
« on: January 15, 2024, 09:20:57 AM »
Would love to see someone post a KNOWN original Shelby carb setup. Thx keith

7
1969-1970 Shelby GT350/500 / Re: Starter cable
« on: January 15, 2024, 09:17:40 AM »
No ,it's a c6 d part number..printed on cable with a cover( sheathing )down by exhaust, believe asbestos,so repo is not the same.

8
1969-1970 Shelby GT350/500 / 1969-70 shelby gt350 choke shield
« on: January 11, 2024, 02:40:15 PM »
would like to know the proper choke heat shield on 69-70 gt350. information so far is the part is listed in the 69-70 parts list as c9zz-9861-B , dont know what that looks like...would love to see an nos one.  know the c9zz-9861-A version is for the 2bbl. version 69 mustangs. have a choke heat shield from a 69 mustang with the 351w 4bbl. carburetor....this will not fit due to the carburetor height reduction on a shelby ,when a different carb spacer is used than a 69 351w 4bbl. mustang. this part is shown on coralsnakes website but has been cut to fit. dont know if ford or shelby modified the production part or was the flat shield version used as seen on some 69-70 gt350 cars. if someone has an original survivor car ,would love pictures. would also like to know what part number in parts book shows for production 69 mustang with 351w 4bbl. engine...any help is appreciated, as goal is to find out what really came on a 69-70 shelby gt350 for a choke heat shield. thx keith

9
1969-1970 Shelby GT350/500 / Re: Starter solenoid repair parts
« on: October 05, 2023, 03:02:26 PM »
yes ,i am looking for the round repair parts, the later nos motorcraft solonoids unfortunately have different internals . thx keith

10
1969-1970 Shelby GT350/500 / Starter solenoid repair parts
« on: October 04, 2023, 08:26:38 PM »
Does anyone sell replacement parts for the c7 and c9 round Dearborn 1969-70 starter solenoid...internal pieces...thx keith

11
1969-1970 Shelby GT350/500 / Re: 1969 GT500 on craigslist----read ad
« on: September 22, 2023, 10:54:09 AM »
I CONTACTED OWNER, AS I OWNED THIS CAR FOR SEVERAL YEARS, HE WAS VERY NICE AND I CLARIFIED THE SCJ WAS NOT DEALER INSTALLED. THX KEITH

12
Wanted to Buy / Re: Original 4 speed Shift knob retaining nut
« on: September 18, 2023, 09:44:59 PM »
Still looking

13
Wanted to Buy / Original 4 speed Shift knob retaining nut
« on: August 26, 2023, 08:23:48 AM »
Wanted 1969/70  4 speed shift knob retaining nut used original or nos thx keith

14
Wanted to Buy / wanted 1969-70 shelby front license plate bracket
« on: July 31, 2023, 03:07:21 PM »
wanted original 69-70 shelby front license plate bracket,thx keith 318-393-1502

15
1969-1970 Shelby GT350/500 / length of 69-70 gt350 air cleaner stud
« on: April 25, 2023, 12:13:00 PM »
what is the length of 69-70 gt350 air cleaner stud.... did shelby or ford  change out the stud for the taller fa-50 element, because the factory stud is too short(regular 351w used a fa-41 and a completely sealing air cleaner lid)...thx keith

Pages: [1] 2 3 ... 11