wanted carburetor tag c9zf-c dated in 9A or early 9B...THX KEITH 318-393-1502
- Welcome to SAAC Forum.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
#63
1969-1970 Shelby GT350/500 / choke shield
February 22, 2022, 03:50:39 PM
could someone please post a picture of a 69-70 gt350 autolite carburetor choke shield...thx keith
#64
Wanted to Buy / Re: wanted..nos or excellant used 69 351w z bar
February 21, 2022, 12:24:15 PM
found,thx
#65
Wanted to Buy / wanted..nos or excellant used 69 351w z bar
February 15, 2022, 12:47:59 PM
wanted c9zz-7528-a 69 mustang 351w z bar...prefer nos but would be interested in nice used with good plating....this bar was used on 69-70 mustang 351w manual transmission cars...thx keith 318-393-1502
#66
Wanted to Buy / Wanted original 69 Shelby shocks,early blue ones
December 26, 2021, 07:19:21 PM
Wanted 1969 Shelby shocks...z7zd adjustable autolites,dated in 9A or early 9B..need nice originals.looking for fronts but will also buy a set....thx Keith 318-393-1502
#67
Swap Meet / Wtt..68 dated Shelby shocks for 69dated ones
December 26, 2021, 07:13:43 PM
Wtt...z7zd front shocks dated early 68 for ones dated in early 69...or will buy outright...need nice originals.. adjustable autolites..have other shocks to trade or buy outright..thx Keith 318-393-1502
#68
Wanted to Buy / bellhousing to block bolts
December 16, 2021, 12:06:28 PM
need original 4spd. bellhousing to block bolts for a 69 351w (gt350), they are 5/8 head solid head with no marking on the head...2 1/4 to 2 1/2 long(under head) with shank under the head followed by course threads...i believe used 67-69 at least, need 4 original bolts...thx keith 318-393-1502
#69
Wanted to Buy / Re: 1969 bellhousing original bolts
November 01, 2021, 12:44:58 PM
thank you,i believe i have found the two short ones with no headmarkings,so just need the 4 long ones,thx keith
#70
Wanted to Buy / 1969 bellhousing original bolts
October 31, 2021, 09:23:41 AM
wanted a set of original 69 351w 4 speed bellhousing bolts to block...2 shorts and 4 long...hex head non indented...usually have 3 slashes and marking like F or m or TR and more. thx keith 318-393-1502
#71
Wanted to Buy / Re: 1969 bellhousing original bolts
October 31, 2021, 09:19:40 AM
I agree especially on the 2 short ones,thx Tim.
#72
Wanted to Buy / 1969 bellhousing original bolts
October 29, 2021, 11:41:28 AM
wanted a set of original 69 351w 4 speed bellhousing bolts to block...2 shorts and 4 long...hex head non indented...usually have 3 slashes and marking like F or m or TR and more. thx keith 318-393-1502
#73
Wanted to Buy / Wanted original 69 rear backing plate plugs
October 23, 2021, 07:22:30 PM
Wanted original rear backing plate plugs...need one bendix..8a and one kelsy Hayes...crosshatch...would like nice used or nos...these are for rear brake backing plates on a 70 Shelby gt350..9 in with 28 spline...thx Keith 318-393-1502
#74
1969-1970 Shelby GT350/500 / Re: 9 inch vent hose clamp
September 12, 2021, 06:32:32 PM
Thank you
#75
1969-1970 Shelby GT350/500 / Re: 9 inch vent hose clamp
September 12, 2021, 06:14:32 PM
Bob ,was speaking if pinch clamp has any stampings ,as mine did not,but my fuel line ones at carburetor did. Thx keith