SAAC Forum

Looking for a unmolested hipo timing cover for a 65 feb/mar engine.

Am having an issue with a 65 speedo plastic driven gear in a T10M transmission. Seems to be eating up gears. Possible wrong pitch driven gear is in there? Are 3 speed and auto driven gears same pitch as 4 speed T10M and toploaders? Is there a pitch mismatch thats cause of problem?

65 GT350 fuel sender wire insulation. Can someone post picture of fuel sender wire under the trunk area. Want to see what type insulation was on original sender wire. And if possible, picture of same yellow wire under the mat in trunk.
Thanks!

Am looking for a nice original 65 Hipo coil mounting bracket and bolt for a 65 GT350 display engine. Must be unmolested original bracket and mounting nut.

Am interested to know what length the black wire from dual point dist to coil was. Also interested to know how dist case was positioned in the block. Any pics of top of coil and dist position is appreciated.

Did Ford/Shelby offer a dual quad setup on the HiPo 290 using Holley carbs as over counter or as option on the Cobras/GT350's?

Can someone tell me what a 65 GT350 Axle Bump stop bracket is and where it mounts? Slipped my mind among other things.
Thanks

I am in need of a fuel line fitting for a 65 GT350 List 3259 carb. It's the brass 1/8NPT to 7/16 fitting on pass side of primary float bowl. 1/8npt is male and 7/16 is female.
Thanks
Martin
5S228

Looking for useable metering blocks for a 65 List 3259 717 Holley carb as found on a 65 GT350. Stamped with part number 3903 on primary and 4560 on secondary.

Is there a list of build and completion dates for the 65 GT350's? I had the data for 5S228, but its filed away. n an undisclosed location...
Thanks
Martin
5S228

I am looking for 2 Emulsion Tubes for a 66-67 3259-1 715 Holley metering block. This is a brass tube, about 1 1/2 inches long that presses into the two inner holes on top of a metering block, believe usually the front. Anyone have ones that are not plugged up and not damaged?
Thanks
Please PM what might have

Harness has a large black wire with red stripe that is a ground. Can someone tell me where correct mounting location for the lug is?
Its a 65 GT350

Thanks
Martin

When Ford balanced the 65 HiPo 289 rotating assembly, did they (Ford) include the flywheel and the thick balancer/hatchet, in the balance? I assume the balance excluded the balancer/hatchet and flywheel as those could be replaced during life of the engine without requiring a rebalance. 

Thanks in advance

Believe Bob Mannels book says to set points in a 65 dual point distributor to .019-.021 which should result in 30-33 degrees of dwell. If you blocked one set of points (A) and adjusted other (B) to 26 degrees dwell, moved block from A and moved it to B, then set dwell on A to 26 degrees, total dwell should be between 30-33 degrees when blocks removed. Would think dwell meter would be much more accurate than a feeler gauge. Thoughts?

I need 2 sets of points for a 65 C50E-12127-F hipo dual point distributor.
NOS in box, Points, DP-6 FDS-12171-N
Thanks

Need to find some components for couple of a C5OF-12127-E 65 Hipo Dual Point distributors. Prefer NOS in box or exceedingly nice used parts.

1. Bushing, lower, C5AZ-12132-A MC-176.Need qty 2.
2. Points, DP-6 FDS-12171-N. Need 4, (2 sets).
3. Distributor gear, Need 1.
4. Spring clip that secures points cam (reluctor) to the distributor shaft. Need 2.
5. Coil wire,. Has molded grommet close to points connector. Need 2.
6. Points cam (reluctor) 13L/18L. C5AZ-12210-A. Need 2.

Thanks
Please PM or e-mail to mygt350@aol.com

Who is the current go to guy for rebuilding and setting up the 65 HiPo dual point distributor for a GTt350.  Have one that needs the right magic fingers to make it spot on correct for a 65 GT350.
PM or e-mail with reliable references/recommendations please.
mygt350@aol.com

Looking for unmolested C4OE-6059-A timing cover with Mar or Apr (preferred) date code. This is the cover used with the alum water pumps on. 65 Hipo engines. Please PM me or send e-mail to mygt350@aol.com
Thanks

Still looking for a nice unmolested 65 GT350 S1MS-9424A stamped intake with PCV port on rear runner. Please e-mail or PM me pics of what you might have hidden away.
Thanks
mygt350@aol.com

Can someone tell me what the correct PCV grommet part number/marking is for a 65 GT350 open letter valve cover?
Thanks!
Martin