SAAC Forum

Is the vin/Shelby number known ??

Looking for a pair of originals for a Non Fold down FB . Cant use any with wallered out holes though,  I have those already

Thanks

Maybe stupid .... no problem , Is there any way or procedure for "bench testing" the console wiring prior to install ?

Thanks !

Anyone have a pic ? This car got new floorpans , toeboards. Plug orientation is up ? right ? or left ? I have searched and couldnt find a pic on a 69 anywhere (:

Thanks, Steve

Quick question... speedo cable , 2 clamps to firewall or one? Have seen both ways , just one on the rt side, and also one on both sides of the tunnel.
Thanks

Yes I have the manual and schematics, just can't figure this one out.
Found these 2 wires, appeared to be cut, maybe the same wire, maybe 2 different ones? Both green, no tracer.
One , I know, goes down to the console harness 4 plug connector- its the one on the right in the pic
The other one (or other end) I cannot figure out
Any help/suggestion is appreciated
Thanks, Steve

BTW 69 500 4-spd, non-air

Hey, can someone post a couple of pics of the routing for the fog light harness from firewall to lights?  I'm waiting for the electrical manual and supplement to come in and just wanted to see how this thing was run.

Thanks for any help !!
Steve

Found a wired bundle of wires under the dash of this 69 500 4spd I'm working on . Anyone seen this or know what all this stuff goes to ?

GT40 seats ?  Wonder who makes these ?

Ok... I think I f-ed up. Replacing the turn signal switch, tilt 68, and I guess I misplaced a wire. No parking lights, turn signals ...unless the emergency flasher switch is pulled out. This is a new NOS switch.
Anyone have the schematic for the plug, or a drawing , with wire colors and positions ?
Thanks !!

I'm helping a friend reassemble a 69 FB . It was purchased painted and rolling  with a bunch of boxes of parts.
I see a hole in each outer wheelhouse .... brake cooling ducts?
Also  found 2 pieces - fiberglass with similar holes in them ... related to above ?
He may have to buy assembly manuals.. Shelby specific
One more... wat type of rivets for vin tag on dash and Shelby plate on apron .. steel ?


Thanks for any help !
Steve

Is this section down ? Been trying to list a car for over a week and get , page cant be reached message

Rt or left or both

Is the brake pedal different for a disc brake car vs drum ?

Thanks !

Hi, looking at short post 2 post lifts. Ceiling height is restrictive (10') so I'm looking at the short post models. Anyone have a good recommendation/experience. I plan on installing my self.... with some help

Thanks

4/68  350, 4spd, a/c vert  would this be the original box ?
OA26- something about this casting date seems wrong to me.
C7ZR 3550A

Tag reads - SMBF  OEI3B

Tried to post a couple of pics but system timed out on me. 

Thanks for any feedback ! Steve

Ok, I admit failure. Twice now I have pulled the console and replaced the woodgrain, (sourced from Branda)and in both cases it has lifted in the curve just below the gauges. Last attempt I even set that curve and the rear one first to avoid stretching the decal..
Open to what has worked for others in the past, contact cement maybe ? Its kind of a PITA job to begin with, but I'm certainly willing to try a new technique.
Thanks in advance for any suggestions .... well except sending to some dude in Canada and spending $700 with a maybe 3 month turn around time

Are 67 small block motor mounts year specific? Talking about the frame rail side.... are they unique to 67 only and different from a 68 ?  Trying to help my son figure out a motor installation issue.

Thanks, Steve

Anyone know where I can get a 4 spd bezel ?

Clear or tinted in good condition, brackets or none.

Thanks