Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Cam shaft

Pages: [1]
1
Concours Talk / Re: Suspension Detailing Guide
« on: June 30, 2019, 12:08:56 PM »
Nicely done as always,
thank you

2
1969-1970 Shelby GT350/500 / Re: Turn signal
« on: May 04, 2019, 06:34:15 PM »
Thanks to both of you
Cam

3
1969-1970 Shelby GT350/500 / Turn signal
« on: May 04, 2019, 09:21:49 AM »
We are getting down to the last few details on the little project, and I apologize if we are dominating the forum.

Should the area around and adjacent the front turn signals be body color?

4
1969-1970 Shelby GT350/500 / Re: Trunk Light
« on: May 02, 2019, 10:51:46 PM »
thank you Ed.

We are going to use a 14 gauge black wire following the same route as lite socket wire, connected to socket  with screw and washer. The question remains,  where and how is it  connected to the body to complete the circuit?

thank you again

5
1969-1970 Shelby GT350/500 / Trunk Light
« on: May 02, 2019, 12:36:26 PM »
Would the trunk light harness,  C9ZB-13550-A (1970 gt500,), require an additional ground wire for a correct installation ?

Thank you

6
1969-1970 Shelby GT350/500 / Pinch weld
« on: October 26, 2018, 09:27:08 AM »
Would  the pinch welds  on a 1970 500  be correctly  finished  as other 1969 mustangs? 

Thank you!!!!

7
1969-1970 Shelby GT350/500 / Re: Front lic. bracket
« on: October 18, 2018, 04:45:41 PM »
Thank you again!

8
1969-1970 Shelby GT350/500 / Front lic. bracket
« on: October 17, 2018, 04:29:25 PM »
Should the front license plate bracket by painted black or plated zinc for 1970, fb,4spd, 500?

thank you!

9
1969-1970 Shelby GT350/500 / Re: dashpot and glove box latch
« on: September 08, 2018, 09:37:54 AM »
Thank you!

10
1969-1970 Shelby GT350/500 / dashpot and glove box latch
« on: September 06, 2018, 03:37:16 PM »
1. Would the correct dash pot for 1970 gt500 4 speed, w/o air, carb# DOZF-9510-AA  be the electric or manual type?

2. Also, would the correct glove box latch for the same car with deluxe interior have the button or the lock?

Thank you 

11
1969-1970 Shelby GT350/500 / Re: Air cleaner seal
« on: August 05, 2018, 02:36:18 PM »
If one found the olds 442 seal,
1. What is the correct thickness for the gt500 application.?
2. Is there a proper and correct method to trim the seal to specs?
3. Would the seal need to be cut to adjust the diameter (i.e. Circumference)?
Thank you

12
1969-1970 Shelby GT350/500 / Rear uarter upper pivot
« on: March 10, 2018, 07:12:55 PM »
Would here be a stainless bracket on the rear quarter panel upper pivot, #30228,  necessary for a correct quarter window  installation?
thank you

13
Concours Talk / Re: caliper and master cylinder color
« on: February 19, 2018, 07:09:55 PM »
Bob,

Thank you,

we are getting closer

14
Concours Talk / caliper and master cylinder color
« on: February 19, 2018, 10:15:04 AM »
We are trying to get the paint colors correct on the little 69 gt500.

1. Were the brake master cylinders painted with the cap in place or was the reservoir masked  off?

2.  Is semi gloss black correct for front brake calipers?

thank you for the help!!!!

Pages: [1]