Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - cbrown

Pages: 1 [2] 3 4 ... 14
16
Does anyone here on the forums live near Greenville That could look at a car for me? I will pay you for your time.

chris

17
Concours Talk / Re: assembly line style air filters
« on: February 20, 2021, 12:12:28 PM »
Ya what Ed said!!!  :)

thanks to everyone for the support...

chris

18
Yes.   Me..    Just did a batch awhile back.   Getting ready to do another.  YOU have to heat up your mirror and remove the glass. 

chris

19
Have you thought about resilvering the mirror?  usually the outer rubber is not bad and can be cleaned up.

chris

20
1969-1970 Shelby GT350/500 / Re: 69-70 console top ashtray odor fix
« on: February 13, 2021, 08:33:08 AM »
Probably around 110.  I used to sell them a little bit cheaper. But the problem was With the jig I had made up I would drill the small holes myself but it would take me over an hour to get one done and would break drill bits because they were so small.  So I have a machine shop that has agreed to do 20 at a time for me which is happening right now.  Mine has the ring around the ashtray also and has the correct knob .   I will do a post when they arrive back and are ready.

Chris

21
1969-1970 Shelby GT350/500 / Re: 69-70 console top ashtray odor fix
« on: February 12, 2021, 10:07:41 PM »
I have them, but am
Out right now    I will have some in about three weeks .I have my machine shop putting the holes in sides for the light to illuminate through so they will be concours  correct.

Chris

22
1968 Shelby GT350/500/500KR / Re: Seam sealer
« on: February 06, 2021, 12:07:48 PM »
This is gun we use.  I do not regulate the pressure down at the gun and the fan control on side of gun is only opened about 1/4 turn.  I do exactly what jeff said.  I do test spray on piece of card board and ge desired pattern and then go at it!!  He is a couple of pic of 67 we just did. I think we have some video of us spraying wheelhouses and floor on instagram if you do that stuff.

chris

23
1968 Shelby GT350/500/500KR / Re: Seam sealer
« on: February 05, 2021, 11:12:08 AM »
Yes, I agree with Tim.  Fusor gun with 805hd product.

chris

24
1967 Shelby GT350/500 / Re: paxton equiped 67 gt350s hood
« on: January 31, 2021, 06:33:28 PM »
Bob,  I have Chris Laytons car at my shop undergoing restoration and it is an early steel framed hood car but has cut out on left side as if needing clearance for paxton.

chris

25
1967 Shelby GT350/500 / paxton equiped 67 gt350s hood
« on: January 31, 2021, 02:39:35 PM »
Where any modifications done to the hood on paxton equiped 67 gt350s?

chris

26
1969-1970 Shelby GT350/500 / Re: convertible interior question
« on: January 26, 2021, 07:43:55 PM »
I stand corrected..  Should have looked  in shop  before posting...lol  IS 68 the style with no screw? I know i have some convertible panels with the style i described in storage.

chris

27
1969-1970 Shelby GT350/500 / Re: convertible interior question
« on: January 26, 2021, 01:07:57 PM »
Tim , I believe snap  with  blind style rivet built it. you cant see form the front side. on backside it sticks thru then  is smashed with washer to hold intact.

chris

28
1968 Shelby GT350/500/500KR / Re: Original owner story and photos - #0738
« on: January 24, 2021, 01:57:02 PM »
OHHH, i see.  Must be the fuel line im seeing because it has autolite carb i assume?

29
1968 Shelby GT350/500/500KR / Re: Original owner story and photos - #0738
« on: January 24, 2021, 01:37:00 PM »
IS that a dual vaccum advance or single?

chris

30
Concours Talk / Re: assembly line style air filters
« on: January 13, 2021, 10:28:21 AM »
Ed, brought to my attention that i did not show the most important part.. 

Pages: 1 [2] 3 4 ... 14