SAAC Forum

When mounting on a alu oil pan, do you use the bolts from the original oil pan ore are there "special" bolts fore this job?
Tor

Hello
This should have been in the flashing yellow section, but I could not figure out how to post there.
But this is the case: I have just been aware of that 9F03M482674 has left Norway and exported to USA.
My advise is STAY away from this car. This car was scrapped in late 70 in Sweden. One bright head here on Norway got hold of the title somewhat, he imported a 70 6 cylinder chassis from Sweden and suddenly this car was back on track again. If you are looking fore a real deal, this is not the car you want. Story of this car is secured with the registrar Vinman

Tor
Norway

Hello
Do anyone have the phone number to Amk fastner?

Tor

Hello
I have probelms with renewal of my subscription,I have tried to send e-mail to Jay Talbot fore over a week, no respond.Do anyone have a phone number to him so I could call him.
Tor

Hello
Those new registerys are very nice,have bought all 3 of them. In the 66 registery there was a size diffrernce on the writing,I liked the size from page 343 and out,it was easyer to read.
Will the editor of the registerys to come please use that size?
The 66 registery was over 670 pages with 2392 cars in it. Those registerys to come will have well over 3000 cars in them,those registerys will be huge with only a glued spine.
Will it be a idea to split those registerys in 350 and 500 editions to keep the size down on them?

Regards
Tor

Hello
On the bj/bk carbs there is a balance tube between the 2 fuel chambers, on the drawing there is a washer and a O ring on both ends on the tube, where can I buy those washers without buy a complete gasket kit fore those carbs.

Tor

Hello
Can anyone id this antenna? Is it a PM 300 ?

Thanks
Tor

Did the fuel pump on the 67 500 have date stamps on them?

Tor

What type of oil do you use on the Detroit locker end, thanks

Tor

In the Ford Hi per parts catalog page 34 is there a induction kit. What carbs is it in this kit? It says 510 cfm carbs.
And which manifold is included here,is it the manifold issued fore the 67 GT 500?

Tor

The 67 Shelbys was shipped from San Jose too Shelby American with out the hood and the rear deck lid.
The car  was painted at Ford San Jose,how did they avoid the paint diffrences that could occur when the hood and deck lid was painted at Shelby?

Tor

Does anyone have the AMk part number fore those nuts?,and also the part number fore the fuel hose clamps fore the fuel log.

Tor

Hello
Does any one here have a e-mail adress fore this gentleman? He is the owner of a super nice 67 350
Please pm me with his adress.

Tor

Is it by day/year , week/year ore quarter/year?

Tor

C90F-9510-H
List 4345
What is this carburetor used on? Price?

Tor

Hello
Can anyone confirm the address to Joe Bunetic (The carb restorer)
Is this his address?

65 Concord drive
Fair view heights Illinois 62208
Usa

Tor

I"m going to take the fuel log of my GT 500 and replate it. Will it be a proplem to remove this one? !"m thinking about it will loosen the sealing fore the intake manifold gasket,any problem here?

Tor

Hello
What is the price of a set with those carbs with matching dates worth?
They are used but not worn out,but need a new plating etc,they also have the brass floats in them
They both have the 4731 metring plate installed.

Regards
Tor

Is this saac member on this forum? What is his name on the forum?

Tor

To you who own a 70 Gt 500,what is the date casting number on your distributor?. How I understand this is that the 70 models should have D0TF casting number, can any owner enlighten me here?

Tor