SAAC Forum

I'm looking for an original inlet for the lower scoop (picture attached).  This is for a 1966 not sure if 67's were the same.

Found this the other day on Marketplace.  Not mine but seems interesting seller says located in Scarsdale, NY


1967 SHELBY GT 350 Early production.289 hipo 4 speed. All early 67 Shelby original parts, Including lucas flame thrower
headlights, hood prop rod, steel frame hood, and trunk lid, running lights on upper scoops in excellent condition.
The paint has some minor flaws,not perfect. Time period correct paxton super charger added.
The first of only 12 1967 Shelbys painted charcoal grey. Matching numbers stamped on block and transmission.
This is a very rare car and color. owner. It was my neighbors car when i first saw it in 1971. I bought the car in 1984.
The car was fully restored in 1991.
headlights,hood prop rod, steel frame hood, and trunk lid,running lights on upper scoops in excellent condition.
The paint has some minor flaws,not perfect .Time period correct paxton super charger added.
The first of only 12 1967 shelbys painted charcoal grey.Matching numbers stamped on block and transmission.
This is a very rare car and color. owner. It was my neighbors car when i first saw it in 1971. I bought the car in 1984.
The car was fully restored in 1991.  https://www.youtube.com/watch?v=GnD9DYq5GxY

I'm getting ready to order my front and rear glass for 6S1816.  I have the original rear glass but the windshield is gone.  ESC is the company I'm using and the are asking a few questions on orientation.  Should the windshield etching be on the outside or inside of the windshield?  Should the orientation of the text be in reverse when looking form the outside?

Thanks

I am looking to purchase an original tachometer optioned instrument cluster housing.  I am converting a non tachometer car 67 C code Mustang, have all of the gauges just need housing.

Thanks

Hi all,

I'm working on a 67 and looking to purchase a very nice driver windshield.  I'm in the York, PA  / Baltimore, MD area and willing to travel an hour or two for the right piece.  Not interested in getting one shipped to me.  Date code not important but must be clear with no shade at top.


Thanks

I'm looking for a rust free 67 or 68 Fastback deck lid. 

I'm looking for a parts car with good original floors.  A 67-68 Coupe body shell or full floor pan already removed will work if correct for 67. 

Willing to arrange shipping etc

PM if you have what I'm looking for

Where can I source the most accurate brake rotors?

I'm looking for a clear direction on paint markings.   I understand there are model year changes etc that effected some of the marks.  My car 6S1816 was built at Ford late March 1966 and left Shelby American 4/26/66.  I have my front and rear springs done with the proper identification marks.  All of the body assembly marks were photographed and duplicated back onto the car.

I need pictures or direction on the following:

Rear housing and center section
Steering linkage
Steering box
pitman arm
Idler arm
Tie rods
Upper / lower control arms
Spindles


Not sure if I'm missing anything but will take any additional info I can get


Thanks

Shawn

When did the early (slight wrap) door panel insert transfer to the later (straight ended)? 

I'm looking for a used original (or used repo) passenger side mirror dummy remote.

Thanks
Shawn

Hi All,

I'm looking for used black carpet for 1967 Coupe/Fastback.  Trying to match patina of original interior.  Does not have to be original just somewhat faded and worn.  If you have reasonably priced OE I'm open to some flaws in the carpet.

Thanks

Shawn

Hi All,

I'm looking for a correct reproduction set of 5 chrome magnums.  I am open to new or used depending condition.  Application is 1966 Shelby with correct backspacing and valve stem location. 

Thanks

I am at the point where I need wheels and tires for 6S1816 Hertz.  Seems suppliers are months out on the 66 Shelby style magnums.  What other options do I have, 10 spokes?  Would 10 spoke wheels be points deduction if on Hertz car for judging?  Anyone out there have a nice set of 66 Magnums available?  I'll post to WTB section once I have an understanding of the acceptable wheels for DIV II judging.

Thanks

Whats the correct finish for 66 brake drums?

Hi All,

I'm looking for 2004-06 dated original Goodyear tires that were factory installed.  Only looking for tires with very good tread remaining.

Thanks

Hi All,


Just wanted to post the name and contact information of the Radiator Shop near me.  I recently dropped of my original 1966 Shelby radiator for re-core.  I'm very impressed with their communications and quality of work in their shop.  They've been in business for over 56 years.  Wayne the owner says he receives radiators being shipped to him regularly.  Nothing in it for me just getting the word out


Shop Name and Contact:

  CR Smith
2515 W Market St.
York, Pennsylvania 17404

717-792-9912
autorepair2515@aol.com

Just delivered my original radiator for re-core at a local shop.  Is there anything available in a spray can that replicates OE finish?  I've used Eastwood radiator black in the past and a difficult time getting it to adhere.  Also looking for a correct petcock source

Thanks

Hi All,

I have 2 original brake duct outlets for trade.  One is missing some pieces and the other is intact with a slight crack (easy fix).  I would like to trade both for an original inlet.  I have attached pictures of the 2 I'm offering and for reference a picture of what I need.

Thanks
Shawn

I'm preparing to install the rear quarter window frames I just recently got back from Shelby Parts.  They are fully assembled and ready to be riveted in place. I'm looking for details on sealer type and area of application around the aluminum frames.  How far to the outside of the frame is the sealer visible if at all? Any pointers on process of installing would also be helpful.