SAAC Forum

Thanks Bob, does the hoses have any type of clips or clamps that attaches the lower hose on the drivers apron?  Or does the line just hang loose? 

Also, wiring harness crossing the front X-member,  my harness is just laying loose on top.  Did Shelby have any special clip for the harness?  Original Ford clips can't be used because of nose cone attached on top of the X-member. 

If anyone needs pix's, I still have the gray clips on the hood support for the inboard light harness and I just replace my original coil spring which have a white, violet and Yellow stripes on them for detailing.

Thanks

Anyone have any pictures showing the correct fasteners and locations of the engine bay wiring harness mounting on the aprons? My harness is also laying loose on top of the front cross member? with no fasteners. 

How is the gauge pod wire harness attached on shock tower brace and is the harness wrapped with a clear plastic sheeting?

Do the power steering lines have any mounting clips and how are these routed, attach on lower apron?  I also need to replace my P/S cooling lines.  My car is mid Feb. GT350 and the lines look like they are textured or are so dried out that the nylon reinforcement is showing.  My lines are original and have never been changed.  Are they textured rubber lines?  Is so, where can I buy the correct rubber hose?

Any suggestions on replacing the head light bulbs for something more brighter?

Thanks for your help...

My 350 built date is mid Feb of 67' and 3rd member is dates early Jan 67'  C7ZX-A 3.89 7A8

Thanks Bob, can't find any date on it only C7ZE stamped into the side frame FoMoCo on the top tank...

Thanks for all the help guys but here's what I'm needing,

Heads C7ZE, 67 289Hipo heads like what was used on K-codes and GT350 Shelby.  I had the machine shop drop and crack one of my original GT350 heads. 

Radiator 24'' Big block GT390 and GT500.  Looking for a San Jose radiator for GT390 car.  The radiator that is in the car is stamped C7ZE but without date code.  My understanding is that only the San Jose radiators were dated on the top tank. Measuring center of mounting holes, it comes in 23'' 3/4

Thanks

Looking for 1967 24'' San Jose 4- speed radiator date coded around late 1966 or early 1967.

Also looking for single or pair of C7ZE heads date coded around the same time as the radiator.

Please send me PM,  Thanks

Did Shelby remove the rear Ford Tie downs and engine lift hooks when they received the car?  Also, what type of clamp was used on the lower scoop to attach the hoses to fiberglass?

Thanks

Anyone have any front suspension detailing picture they could post?  Looking for what parts are natural steel and what were painted.

Thanks

Does anyone know who is still building or can build a custom aluminum radiator for 67'? 

Mark 7 Custom Aluminum Radiators is now closed from what I understand.

Thanks

I have a friend looking for 1970 GT350 or GT500 Shelby. Nice driver condition, older restored car or needing repair.

Please send me PM if you know of any or come across a car.

Thanks

Okay so the tail light harness does have the clear w/blue stripe connectors and front inboard head lights have no white scotch loks on them. 

Who is selling the correct white scotch loks?

Thanks for all your help.....

February car

Does any one have pictures of the original way or connectors Shelby connected the front inboard light wiring into the front harness and also for the tail lights into rear trunk harness. 
On my car, harness wire insulator coating has been cut off and the wires wrapped around each other and electrical taped.  Is this how it was done?

Thanks for the help...

Can you tell me who sells and has the most detailed 1967 Mustang restoration book?   Looking for interior paint colors, other detailing undercarriage and under hood info.

Thanks for the help

Going with the curly ones............

Thanks for all the help...