News:

SAAC Member Badges are NOW available. Make your request through saac.memberlodge.com to validate membership.

Main Menu

Master Cylinder Cap 1967 GT500 which is correct

Started by Kent, January 30, 2019, 10:17:36 PM

Previous topic - Next topic

Kent

I´m wondering about the Master Cylinder Cap on the GT500 67 because I have seen several styles from natural over galvanized etc. on concours GT500´s which one is correct? Thanks for helping...
SAAC Member from Germany and Owner of a unrestored 1967 Shelby GT500, 1968 1/2 Cobra Jet´s and some nice Mustang Fastback´s 67/68

JD

'67 GT350 and GT500 caps are the same (Ford Mustang part), there is a difference of early (top) vs later (bottom).

Note the vents, "domes" and the stickers differ.  Painted semi-gloss black.





'67 Shelby Headlight Bucket Grommets https://www.saacforum.com/index.php?topic=254.0
'67 Shelby Lower Grille Edge Protective Strip https://www.saacforum.com/index.php?topic=1237.0

Kent

ok these ones are totally different to the most I have seen on 1967 Shelby´s
SAAC Member from Germany and Owner of a unrestored 1967 Shelby GT500, 1968 1/2 Cobra Jet´s and some nice Mustang Fastback´s 67/68

JD

...also, the text on the rear dome is de-bossed into the lid, not raised up, providing a flatter surface for sticker.
'67 Shelby Headlight Bucket Grommets https://www.saacforum.com/index.php?topic=254.0
'67 Shelby Lower Grille Edge Protective Strip https://www.saacforum.com/index.php?topic=1237.0

Kent

Is there a repro or a source where I can buy the later style?
SAAC Member from Germany and Owner of a unrestored 1967 Shelby GT500, 1968 1/2 Cobra Jet´s and some nice Mustang Fastback´s 67/68

JD

I don't off-hand know of one, but it is a "standard" Ford part.  Maybe someone will see this and can sell/ship you one as it looks like you are overseas.  Maybe Bill Collins?

'67 Shelby Headlight Bucket Grommets https://www.saacforum.com/index.php?topic=254.0
'67 Shelby Lower Grille Edge Protective Strip https://www.saacforum.com/index.php?topic=1237.0

Bob Gaines

Quote from: Kent on January 30, 2019, 10:32:54 PM
ok these ones are totally different to the most I have seen on 1967 Shelby´s
Most likely that is because the 67 Shelby's you are looking at do not have that detail correct. 
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

2112


Kent

SAAC Member from Germany and Owner of a unrestored 1967 Shelby GT500, 1968 1/2 Cobra Jet´s and some nice Mustang Fastback´s 67/68

JD

The master cylinder, lid, bail and booster were all painted semi-gloss black as an assembled unit and then installed in the car. 
The Sticker (early/late) should be there.  Stickers, both versions, are available from multiple Mustang parts sellers.

(Many cars are restored incorrectly, one of the dangers of copying others work.)
'67 Shelby Headlight Bucket Grommets https://www.saacforum.com/index.php?topic=254.0
'67 Shelby Lower Grille Edge Protective Strip https://www.saacforum.com/index.php?topic=1237.0

roddster

  Kent, the cars are more than 50 years old.  Ya think the master cylinder might have been replaced a couple of times?

Kent

My master cylinder is the original one, cap also now that i know which one it is, i always thought its wrong because all the others Shelbys had different ones.
SAAC Member from Germany and Owner of a unrestored 1967 Shelby GT500, 1968 1/2 Cobra Jet´s and some nice Mustang Fastback´s 67/68