Author Topic: For a '67 GT 4spd. Coupe  (Read 652 times)

Survivor

  • Jr. Member
  • **
  • Posts: 84
    • View Profile
For a '67 GT 4spd. Coupe
« on: February 04, 2019, 12:23:21 PM »
Looking for the following nos or good used condition:
* trunk mat & fiber board
* radiator cap
* low fuel sending unit (convenience control panel car)
* antenna
* aqua carpet set
* shifter boot
* air filter for smog system
* intermediate muffler
* vacuum advance unit
* door bumpers   

J_Speegle

  • Hero Member
  • *****
  • Posts: 1181
  • Just here to help :)
    • View Profile
    • ConcoursMustang.com
Re: For a '67 GT 4spd. Coupe
« Reply #1 on: February 04, 2019, 01:32:56 PM »
* air filter for smog system

Are you looking for the metal canister/air filter housing or the foam filter inside that unit?
Jeff Speegle- Mustang & Shelby detail collector, ConcoursMustang.com babysitter :) and Judge

Dizzy

  • Full Member
  • ***
  • Posts: 125
    • View Profile
Re: For a '67 GT 4spd. Coupe
« Reply #2 on: February 04, 2019, 01:56:27 PM »
I can help with vacuum advance. Please let me know more info....complete or diaphragm ?

BGlover67

  • SAAC Member
  • Hero Member
  • *
  • Posts: 1036
  • Formally "My Shelby Dream"
    • View Profile
Re: For a '67 GT 4spd. Coupe
« Reply #3 on: February 04, 2019, 03:36:10 PM »
I have a shifter boot
Thanks,
Brian Glover
SAAC Carolina's Northern Representative

Survivor

  • Jr. Member
  • **
  • Posts: 84
    • View Profile
Re: For a '67 GT 4spd. Coupe
« Reply #4 on: February 05, 2019, 09:00:45 PM »
Also looking for a fan shroud w/ rectangular logo which I believe would be correct for a very early SJ built car and a battery tray.  Thx.

Bob Gaines

  • SAAC Member
  • Hero Member
  • *
  • Posts: 2509
  • Original Posts:14706
    • View Profile
Re: For a '67 GT 4spd. Coupe
« Reply #5 on: February 05, 2019, 09:21:01 PM »
Also looking for a fan shroud w/ rectangular logo which I believe would be correct for a very early SJ built car and a battery tray.  Thx.
Just in case you were not aware, the battery tray is also 67 specific with pre drilled holes for vacuum canister mounting which changed late in production.
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

stangman39

  • Full Member
  • ***
  • Posts: 177
    • View Profile
Re: For a '67 GT 4spd. Coupe
« Reply #6 on: February 06, 2019, 08:56:45 AM »
WCC has a low fuel sender on their site but out of stock.  Not sure if or when they are getting more.
A 67 GTA 390 FB I had still had the factory one in the tank.  I was surprised to see that.

Bigblock

  • Jr. Member
  • **
  • Posts: 73
    • View Profile
Re: For a '67 GT 4spd. Coupe
« Reply #7 on: February 06, 2019, 12:49:09 PM »
WCC has a low fuel sender on their site but out of stock.  Not sure if or when they are getting more.


Most vendors that had those don't anymore due to wrong resistance on the slider. Your gauge won't read correct.
The manufacturer so far hasn't made a correction.

1967 eight barrel

  • Hero Member
  • *****
  • Posts: 759
    • View Profile
Re: For a '67 GT 4spd. Coupe
« Reply #8 on: February 08, 2019, 05:13:03 PM »
West Coast Cougar and NPD offer a conversion that is solid state that plugs into the factory relay and only requires pushing one terminal out of the relay block and running two leads to the fuel gauge. I put one in my Shelby and it works better than the Ford unit.  It comes with a solid state board that plugs into the relay block, a solid state dash voltage regulator and the two leads that go to the fuel gauge and back to the terminal block. The impossible to find sending unit becomes irrelevent.
                                                                                  -Keith

https://secure.cougarpartscatalog.com/elfi78.html?attribs=75
Once you have tasted flight, you will forever walk the earth with your eyes turned skyward. For there you have been, and there you will always long to return.
"If It's Not Boeing, I'm Not Going!"