Author Topic: PCV Valve, Fitting and Hose  (Read 538 times)

johnzajc@gmail.com

  • Full Member
  • ***
  • Posts: 158
    • View Profile
PCV Valve, Fitting and Hose
« on: October 15, 2019, 09:19:04 PM »
Looking for ---Fomoco C7AE A PCV Valve  [45]                                                                                                                                                                  Block--Gold Cadmium, block shaped, right angle fitting  C80E B

1967 eight barrel

  • Hero Member
  • *****
  • Posts: 828
    • View Profile
Re: PCV Valve, Fitting and Hose
« Reply #1 on: October 18, 2019, 09:24:45 AM »
They are both reproduced. Is this for a '67 500? 
                                                                     -Keith
Once you have tasted flight, you will forever walk the earth with your eyes turned skyward. For there you have been, and there you will always long to return.
"If It's Not Boeing, I'm Not Going!"

1967 eight barrel

  • Hero Member
  • *****
  • Posts: 828
    • View Profile
Re: PCV Valve, Fitting and Hose
« Reply #2 on: October 18, 2019, 05:56:43 PM »
There is no part number on my original block. The PCV was an NOS unit. The part number is on a plastic disc that slides over the threads.  They sell the disc separately. Perhaps Bob can provide you the number if it's missing.
Once you have tasted flight, you will forever walk the earth with your eyes turned skyward. For there you have been, and there you will always long to return.
"If It's Not Boeing, I'm Not Going!"

J_Speegle

  • Hero Member
  • *****
  • Posts: 1295
  • Just here to help :)
    • View Profile
    • ConcoursMustang.com
Re: PCV Valve, Fitting and Hose
« Reply #3 on: October 18, 2019, 06:00:05 PM »
Long are the discussions about the ID tags/rings on the PCV valves and if they were present on assembly line units.

Invite each to do their research focusing on their specific year and application as patterns may vary ;)

Of course there are always owners/builders that will purchase and apply every sticker and label available believe that they are correct for their car.
Jeff Speegle- Mustang & Shelby detail collector, ConcoursMustang.com babysitter :) and Judge

Bob Gaines

  • SAAC Member
  • Hero Member
  • *
  • Posts: 2767
  • Original Posts:14706
    • View Profile
Re: PCV Valve, Fitting and Hose
« Reply #4 on: October 18, 2019, 10:18:22 PM »
There is no part number on my original block. The PCV was an NOS unit. The part number is on a plastic disc that slides over the threads.  They sell the disc separately. Perhaps Bob can provide you the number if it's missing.
The 90 degree fitting block does not have any number markings. The pcv on the other hand will have the C7 in the case of 67 and C8 in the case of the 69 engineering numbers. FYI the 69 pcv will be black chromate and not silver like the C7 PCV. I have seen too many survivor cars without to think that the paper ring was installed from the factory. It was more a service part identification IMO.
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

1967 eight barrel

  • Hero Member
  • *****
  • Posts: 828
    • View Profile
Re: PCV Valve, Fitting and Hose
« Reply #5 on: October 22, 2019, 09:24:48 AM »
^^^^^ Amen.  It's quite confusing when you lack good reference.  Some sellers have burnt many because of just this issue. It's why I deferred you to Bob on this one. My C7 valve has the ring. It was an NOS Autolite in the box. I didn't know if the ring belonged or not.
                                                                                          -Keith
Once you have tasted flight, you will forever walk the earth with your eyes turned skyward. For there you have been, and there you will always long to return.
"If It's Not Boeing, I'm Not Going!"

Coralsnake

  • SAAC Member
  • Hero Member
  • *
  • Posts: 1945
  • Original Posts: 10,264
    • View Profile
    • theCoralsnake.com
Re: PCV Valve, Fitting and Hose
« Reply #6 on: October 22, 2019, 09:33:13 AM »
Jeff's advice is sound. You should be doing your own research and not taking the word of the seller
Shelby researcher, theCoralsnake.com webmaster, the official Conelec Public Information Officer / CEO

gt350hr

  • Hero Member
  • *****
  • Posts: 1083
  • Randy Gillis in real life - 5353 original posts
    • View Profile
Re: PCV Valve, Fitting and Hose
« Reply #7 on: October 22, 2019, 01:32:13 PM »
 Assembly plants used the engineering numbers when assembling vehicles-engines-transmissions, etc. , not parts and service part numbers. Plastic rings would not be on assembly line parts. Many times there is a VERY distinct difference between an NOS service part and an assembly line part , other times they are the same.
Celebrating 44 years of drag racing 6S477 and no end in sight.

1967 eight barrel

  • Hero Member
  • *****
  • Posts: 828
    • View Profile
Re: PCV Valve, Fitting and Hose
« Reply #8 on: October 23, 2019, 04:42:20 AM »
Well, I have seen labels on parts on untouched cars.  However, I agree. Most are just the engineering numbers stamped in. One on a 19,000 coup A/C clutch over the weekend.
                                                         -Keith

                                             
                                                                                                                   
















Once you have tasted flight, you will forever walk the earth with your eyes turned skyward. For there you have been, and there you will always long to return.
"If It's Not Boeing, I'm Not Going!"