News:

We have implemented a Photo Gallery for hosting images right here on SAACFORUM. Check the How-To in News from HQ

Main Menu

Stewart Warner 240A fuel pump

Started by mlplunkett, January 30, 2020, 11:38:43 PM

Previous topic - Next topic

shelbydoug

I've had an electric fuel pump in my trunk since 1972. It hangs off of the deck lid hinge mounting bracket. It works fine there.

That technically is less the 24 inches to the bottom of the tank.

Tt works so well, in fact, it really sucks.

Why put one under the car? It will be exposed to all types of road hazards?

If need be, put a pump on the end of the pick up tubes in the tank like the new cars use.

This seems like a no brainer to me unless you are intentionally making it more complicated then necessary? I know people like that.
68 GT350 Lives Matter!

pbf777

Quote from: CSX2259 on March 13, 2020, 04:37:52 PM
Here is the photo of 002 as I promised......


     This would be a more correct for proper function installation versus any in the trunk endeavor; and safer for the car and the occupants from a fire hazard also!     ;)

     And before someone says "bah-humbug", please Randy (jump in!  :) ) mention the NHRA rules concerning the requirement of no fuel lines or related fuel components (this includes direct operating mechanical fuel pressure gauges) in the occupant compartment and the requirement of a bulkhead (not just the rear seat assembly) separating occupants from trunk mounted fuel system components.         ;)

     Scott.

Bob Gaines

Quote from: pbf777 on March 13, 2020, 09:08:37 PM
Quote from: CSX2259 on March 13, 2020, 04:37:52 PM
Here is the photo of 002 as I promised......


     This would be a more correct for proper function installation versus any in the trunk endeavor; and safer for the car and the occupants from a fire hazard also!     ;)

     And before someone says "bah-humbug", please Randy (jump in!  :) ) mention the NHRA rules concerning the requirement of no fuel lines or related fuel components (this includes direct operating mechanical fuel pressure gauges) in the occupant compartment and the requirement of a bulkhead (not just the rear seat assembly) separating occupants from trunk mounted fuel system components.         ;)

     Scott.
From a historical stand point and to be fair didn't the rules changed after the 60's time period we are talking about ?
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

gt350hr

   Yes Bob IIRC it was 74-75 when the rules were changed by NHRA.
        Randy
Celebrating 46 years of drag racing 6S477 and no end in sight.

pbf777

Quote from: Bob Gaines on March 13, 2020, 09:14:54 PM
From a historical stand point and to be fair didn't the rules changed after the 60's time period we are talking about ?


     Definitely, but I was attempting only to point out a "more correct for proper function installation" and safety, and agreed, perhaps not a more typical period correct installation. 

     But, perhaps, if I had the out of the example of car #002 as presented (if "period correct" if that still being of a steadfast concern) and my car didn't originally ("day-one") come equipped with such anyway, then perhaps, particularly if I was adding such from need for truly greater fuel delivery than that which solely the mechanical pump was able (say for track day events), then perhaps this alternate installation with its' superior attributes in function & safety could be considered?          :)

      Scott.

       

   

R-MODEL1965

I was wondering if anyone knows whether the bowl, bowl retainer, top plate, and mounting bracket were stainless on the 240a fuel pump or were they zinc plated?

Bob Gaines

Quote from: R-MODEL1965 on June 30, 2020, 06:56:35 PM
I was wondering if anyone knows whether the bowl, bowl retainer, top plate, and mounting bracket were stainless on the 240a fuel pump or were they zinc plated?
Not stainless steel. Those parts are zinc plated steel.
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

dmb496

I see the SW240A complete gasket kit is available again on Ebay.

David

gt350hr

Quote from: Bob Gaines on June 30, 2020, 07:55:03 PM
Quote from: R-MODEL1965 on June 30, 2020, 06:56:35 PM
I was wondering if anyone knows whether the bowl, bowl retainer, top plate, and mounting bracket were stainless on the 240a fuel pump or were they zinc plated?
Not stainless steel. Those parts are zinc plated steel.

    +1 and poorly done at that! VERY thin coating that virtually rubs off.
   Randy
Celebrating 46 years of drag racing 6S477 and no end in sight.

Bob Gaines

#54
Quote from: dmb496 on September 21, 2020, 09:32:26 AM
I see the SW240A complete gasket kit is available again on Ebay.

David
A lot of people are under the misconception that the gasket set is what is needed to rebuild a non working pump. The gasket kit is very helpful but it doesn't typically solve the problem of a non working pump. There is a internal switch that goes bad that renders the pump inoperable. That is at the root of the vast majority of non working 240A pumps.  The switch unfortunately is not readily available. I have had a few NOS internal switch's over the years but they are like hens teeth in finding them.
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

mlplunkett

67 GT500 tribute under construction
65 R-model tribute under construction

SHELBYGT350R

Does anyone know how many Gallons per hour (GPH) the 240a pumper?  Thanks


gt350hr

 They were pretty poor like 80. I tried to fill a 55 gallon drum once and it took forever. A Rotary pump is WAY faster!!!
Celebrating 46 years of drag racing 6S477 and no end in sight.

pbf777

Quote from: gt350hr on October 22, 2020, 05:47:29 PM
They were pretty poor like 80.


     If that's G.P.H.?  I think your being awfully kind there Randy; or is that with the 18 volt battery system?        :)

     I think they were probably rated more likely around 50 to 55 G.P.H. (and I'm not sure whether that was "free-flow" (probably   :-\  ) or at pressure, and if so at what pressure, as it was an adjustable pressure unit?); and this equates to something in excess of 300 lbs. per hour of fuel, which at the old stand-by value of one half pound fuel per hour per horsepower would indicate the pump was tapped-out at anything approaching 600 H.P. or more; and this would have been in the best of installations I'm sure.     

     As I remember (in the "old-days"  ::)  ), in the real world, the practice was that one pump was sufficient perhaps to 400 H.P. +/- applications but after that you went with a dual pump installation, again, in reasonable executions of installations, which still would prove to compromise the claimed performance obviously available under only "ideal" conditions.           :)

     Scott.

Bob Gaines

They were optimum at the time but obsolete compared to today's technology. Their use should be for nostalgia purposes only IMO.
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby