Author Topic: 69 GT 350 rotors  (Read 566 times)

shelbydreamer

  • Newbie
  • *
  • Posts: 3
    • View Profile
69 GT 350 rotors
« on: February 03, 2020, 07:22:27 AM »
Hello all, Iím looking for a pair of rotors for a 69 GT 350.

Thank you
Philip
Philip@electrogas.ca

Coralsnake

  • SAAC Member
  • Hero Member
  • *
  • Posts: 3577
  • Original Posts: 10,264
    • View Profile
    • theCoralsnake.com
Re: 69 GT 350 rotors
« Reply #1 on: February 03, 2020, 07:39:26 AM »
I think we just had this conversation 🤔

There are two sizes and it depends on when the car was built
Shelby researcher, theCoralsnake.com webmaster, Conelec CEO

Mongo

  • SAAC Registrar
  • Jr. Member
  • *
  • Posts: 57
    • View Profile
Re: 69 GT 350 rotors
« Reply #2 on: February 03, 2020, 10:11:28 AM »
your build date or v.i.n. would indicate small or big bearing rotors?

shelbydreamer

  • Newbie
  • *
  • Posts: 3
    • View Profile
Re: 69 GT 350 rotors
« Reply #3 on: February 05, 2020, 08:10:24 PM »
Thanks all, to clarify, I'm looking for rotors as I don't have any. I do have the following spindles:

KXX - 2413
DOZA - 3107 C

Looks like after searching this site and the BOSS 302 website, i may be looking at the most difficult part to get for these cars.

If any of you purchased them recently from Branda or NDP and really truthfully wont use them, I would be very happy to buy them from you and let you make some profit.

For future information, here are the dimensions of spindles KXX and DOZA in that order. I can send someone a picture if they know how to load pictures to illustrate better where i took these dimensions from. Not too sure if I'm describing them correctly.

Dust shield mount : 1.9345 and 1.934
Spindle dia. right next to dust shield: 1.369 and 1.368
Spot at taper end right after the threads for the outer bearing retaining nut and thru-hole for the cotter key: 1.152 and 1.154
Dia. just before threads: 0.8415 and 0.841

Thanks all

Philip

Bob Gaines

  • SAAC Member
  • Hero Member
  • *
  • Posts: 4892
  • Original Posts:14706
    • View Profile
Re: 69 GT 350 rotors
« Reply #4 on: February 05, 2020, 08:45:16 PM »
Thanks all, to clarify, I'm looking for rotors as I don't have any. I do have the following spindles:

KXX - 2413
DOZA - 3107 C

Looks like after searching this site and the BOSS 302 website, i may be looking at the most difficult part to get for these cars.

If any of you purchased them recently from Branda or NDP and really truthfully wont use them, I would be very happy to buy them from you and let you make some profit.

For future information, here are the dimensions of spindles KXX and DOZA in that order. I can send someone a picture if they know how to load pictures to illustrate better where i took these dimensions from. Not too sure if I'm describing them correctly.

Dust shield mount : 1.9345 and 1.934
Spindle dia. right next to dust shield: 1.369 and 1.368
Spot at taper end right after the threads for the outer bearing retaining nut and thru-hole for the cotter key: 1.152 and 1.154
Dia. just before threads: 0.8415 and 0.841

Thanks all

Philip
Are you saying that Branda and NPD are out of the rotors now?
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

shelbydreamer

  • Newbie
  • *
  • Posts: 3
    • View Profile
Re: 69 GT 350 rotors
« Reply #5 on: February 05, 2020, 08:54:47 PM »
Yes, Branda just sold out about three weeks ago. NDP couldn't tell me how long they've been out of stock.

Philip

Bob Gaines

  • SAAC Member
  • Hero Member
  • *
  • Posts: 4892
  • Original Posts:14706
    • View Profile
Re: 69 GT 350 rotors
« Reply #6 on: February 05, 2020, 11:11:22 PM »
Yes, Branda just sold out about three weeks ago. NDP couldn't tell me how long they've been out of stock.

Philip
Your only choice is to press some new rotor hats onto the special hubs . NPD sells the separate rotor hats now.
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby