News:

SAAC Member Badges are NOW available. Make your request through saac.memberlodge.com to validate membership.

Main Menu

Power Steering Pump Adjustment Tool?

Started by 1967 eight barrel, February 05, 2020, 09:03:27 PM

Previous topic - Next topic

1967 eight barrel

Did Ford use a specialty tool to adjust the power steering pumps? If so, does someone have a picture?

                                                                      -Keith

Bob Gaines

Quote from: 1967 eight barrel on February 05, 2020, 09:03:27 PM
Did Ford use a specialty tool to adjust the power steering pumps? If so, does someone have a picture?

                                                                      -Keith
Do you mean for tightening the belt?
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

1967 eight barrel

Yes, Bob.  It's almost impossible to get the belt adjusted because of the canister filter.

                                                                          -Keith

Bob Gaines

Quote from: 1967 eight barrel on February 05, 2020, 11:12:27 PM
Yes, Bob.  It's almost impossible to get the belt adjusted because of the canister filter.

                                                                          -Keith
First off the canister filter is not supposed to be on your car so if you choose to use it instead of the factory setup then that is your choice to make it harder on yourself. I don't know about a special tool but there is a casting on the front of your pump that is meant to slid a open end wrench on to lever the pump belt tight. I hope this helps.
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

1967 eight barrel

#4
Bob, do you have a picture of how it's done? I did notice a couple of possibilities. However, I was using a pry bar to get it done. I ran the filter after making up a pattern for Inline Tube for clearance of the power steering pump reservoir.

                                                                                          -Keith

Bob Gaines

Quote from: 1967 eight barrel on February 06, 2020, 12:17:57 AM
Bob, do you have a picture of how it's done? I did notice a couple of possibilities. However, I was using a pry bar to get it done. I ran the filter deliberately after making up a pattern for Inline Tube for clearance of the power steering pump reservoir.

                                                                                          -Keith
I think it shows in the shop manual but if you can't find it let me know and I will get a pump out and take a picture. FYI the 67 GT500 didn't use the inline filter because the fuelpump had the screw on filter made into it . For those reading The 427 use the inline filter on duel four applications because the fuelpump they used (AC brand) did not have a filter.If you want a more inexpensive non button top one that can be rebuilt here is a random one I found on ebay . https://www.ebay.com/itm/1962-63-64-Ford-Galaxie-Custom-292-352-390-406-New-Carter-Fuel-pump-M3915-usa/372877506540   .   
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

Royce Peterson

I looked in the shop manual and was unable to find any illustration or even a description of how to adjust the belt tension. I've always used a short (maybe 12") breaker bar with one end on the shaft of the PS pump while lifting the handle with the shaft under the lifting tab on the PS pump aluminum bracket. So the handle of the bar is right next to the windshield washer bottle. A big square shanked screwdriver works just as well. I don't see how it would matter if there was a fuel filter canister.   


Quote from: Bob Gaines on February 06, 2020, 01:18:43 AM
Quote from: 1967 eight barrel on February 06, 2020, 12:17:57 AM
Bob, do you have a picture of how it's done? I did notice a couple of possibilities. However, I was using a pry bar to get it done. I ran the filter deliberately after making up a pattern for Inline Tube for clearance of the power steering pump reservoir.

                                                                                          -Keith
I think it shows in the shop manual but if you can't find it let me know and I will get a pump out and take a picture. FYI the 67 GT500 didn't use the inline filter because the fuelpump had the screw on filter made into it . For those reading The 427 use the inline filter on duel four applications because the fuelpump they used (AC brand) did not have a filter.If you want a more inexpensive non button top one that can be rebuilt here is a random one I found on ebay . https://www.ebay.com/itm/1962-63-64-Ford-Galaxie-Custom-292-352-390-406-New-Carter-Fuel-pump-M3915-usa/372877506540   .
1968 Cougar XR-7 GT-E 427 Side Oiler C6 3.50 Detroit Locker
1968 1/2 Cougar XR-7 428CJ Ram Air C6 3.91 Traction Lock

Coralsnake

The original Influencer, check out www.thecoralsnake.com

Bob Gaines

Here is a picture of the boss on the front of the pump meant for adjustment .I use a 9/16 open end. I have never seen the Ford tool but I am sure you could fabricate a tool that would make it even easier.
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

1967 eight barrel

That's Lisle part #12400. This is what is used to adjust the belt.

1967 eight barrel

#10
Bob, The bracket is chrome plated and I don't want to mar it getting the belt tight enough that it doesn't slip under load.
                                                                                                                                      -Keith

Coralsnake

#11
I patterned this tool after one a Ford mechanic was using.

It is a modified pry bar (left). I cut the shovel end off leaving 15" of 1/2" square stock coming out of the handle. The shaft was bent to 90 degrees, 11" down, leaving 4" . I rubber coated the end to prevent marring.

Works like a charm. You can tighten the belt tighter than tight. The boss of the ps bracket sits right where the bar bends and you push the handle towards the battery. Presto! You can make this for $10

The original Influencer, check out www.thecoralsnake.com

1967 eight barrel

I like! Simple and I can get the belt tight!
                                                              -Keith

shelbydoug

Quote from: 1967 eight barrel on February 06, 2020, 12:17:57 AM
Bob, do you have a picture of how it's done? I did notice a couple of possibilities. However, I was using a pry bar to get it done. I ran the filter after making up a pattern for Inline Tube for clearance of the power steering pump reservoir.

                                                                                          -Keith

You should have warned me? Now I'm blinded by the glare off of the chrome. :o
68 GT350 Lives Matter!