Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Scode67FB

Pages: [1]
1
Appeals / Smog Tube Repair
« on: June 22, 2022, 12:53:18 AM »
Does anyone repair / restore smog tubes? I have these tubes that came off a 67 Fairlane 390. You can see by the pics that someone cut these off apparently with a hacksaw in order to pull the heads off the motor in the car. Thanks for any leads.



2
Parts For Sale / For Sale: 68 "S" Code Carb
« on: January 25, 2022, 02:10:47 AM »
C80F-9510-D

What you see is what you get. Missing transfer tube but otherwise appears complete and unmolested.
$150 plus shipping.






3
Parts For Sale / For Sale: Mexican 302 Main Caps
« on: January 25, 2022, 02:03:41 AM »
Complete set of Mexican 302 main caps and bolts. $400 shipped.


4
Parts For Sale / FOR SALE: Nodular Third Member And 31 Spline Axles
« on: August 27, 2021, 03:02:48 AM »
I have this Nodular third member to sell. It has a"7F2" casting date, 3.50 gears and a 31 spline open carrier. It has an incorrect yoke on it, but it appears to have been run that way for some time and still in good shape. I struggled to determine a value on it so since it falls in the vicinity of "Spec Case" and "68 GT500" dates, I'll start there. $1200 plus shipping.








I also have the matching 31 spline axles for this. They fit 67-70, but I guess are "correct" for 68-70. One has a visible "C8OW" casting. The other is not clear at all. They both appear to be in very good shape, but both will need to have the collars behind the bearings replaced. One is missing altogether and the other looks like it was used in a housing with a 28 spline axle seal. $450 plus shipping. See pics.





5
Concours Talk / 1967 And 1968 Production Dates
« on: June 09, 2021, 01:48:14 AM »
When did the 67 production end, and when did the 68 production begin? Search function wasn't much help.

6
SAAC Forum Discussion Area / Shelby In A Junkyard!!!
« on: November 28, 2020, 01:42:09 AM »



Bet that got your motor running.

7
SAAC Forum Discussion Area / 289 Cam ID
« on: May 28, 2020, 04:23:29 AM »
Just wondering if anyone can help ID this cam. It came out of the HiPo 289 I'm parting out.  From what I've been able to find, the HiPo solid lifter cams were marked "VE" (actually an upside down "A" instead of "V" but can't type upside down here). The 260 hydraulic lifter cams were marked "UA." This cam is marked "XUA" but does have the orange paint behind the distributor gear like the HiPo cam. The engine did have solid lifters. Any ideas?


8
Parts For Sale / For Sale: 67 Shelby Headlight Buckets
« on: May 22, 2019, 04:27:45 AM »
Headlight buckets from 1960 Galaxie. A few pairs available.
$100 plus shipping for two.
$200 for a set of four, includes EITHER the 1960 Galaxie headlight harness OR free shipping.


9
Parts For Sale / For Sale: FE Parts
« on: May 22, 2019, 04:11:01 AM »
AC brackets. Compressor mount and support/idler bracket. Left: 67-68. Right: 69-70. $100 for either pair.


68-70 Smog and alternator brackets. $100 each.
Three-groove pulleys: $50 each. Also have lots of single- and dual-groove available if interested.
Power Steering adjuster bracket: $50
Power Steering cooler: $50



I believe I only have the one smog pump adjuster. Other than that, I have multiples of everything listed.
Shipping extra.

10
Parts For Sale / F/S 64' 289 HiPo Heads
« on: February 12, 2019, 03:44:53 AM »
$1000 plus shipping for the pair. "C3OE-F" casting number and both have "3J19" casting date.






11
Parts For Sale / F/S Early HiPo Alternator Pulley
« on: February 12, 2019, 03:36:44 AM »
Early pulley with free alternator $100.




12
Parts For Sale / 1964 HiPo Shortblock
« on: November 19, 2018, 02:37:00 AM »
I have for sale a "C4OE" 5-bolt 289 HiPo block w/ "3L21" casting date, that is currently +.030. Includes crank and non-HiPo rods. Assembly also includes "C5" HiPo balancer, timing cover for aluminum water pump and manual flywheel. The block has no VIN on it but has the Ford sequence number (3179) and assembly date (3M4) stamped on it. Altogether these numbers should make it correct for many 1964 models including Fairlane, Comet or Shelby Cobra. Looking for $2000 for this. Would prefer local pickup on this. Shipping would be difficult for me since I don't have a truck right now but may be able to work it out. Located in Cerritos, CA.




13
SAAC Forum Discussion Area / Need Help Identifying 64' 289 HiPo Block
« on: August 26, 2018, 06:26:59 AM »
Hi All,
New member here. I've been reading this Forum for years but never registered since I don't own a Shelby. I've tried to get help with this on other Forums that I'm a member of but have had little success. Here's the deal. I recently acquired a 289 HiPo motor of miss-matched date codes. The block is a "C40E-6015-C (5-bolt) with a "3L21" date code. I think it's too early for a 65' Mustang. I suppose it could be okay for a 64' Fairlane. I can't see a VIN on it in the usual spot for a Mustang. I don't know if Fairlanes got the same treatment. I haven't found any info on them. Somewhere on this Forum I read that the blocks for the 289 Cobras were marked differently. I can't find the thread now, but it stated that the Cobras had the VIN or some other identifying marks stamped on the left side of the block. I don't remember if the markings are supposed on or near the rear of the block. I also don't remember what the markings are supposed to look like. The only things I van find are a group of four numbers stamped onto a smooth pad just below the deck near the left rear of the block. Is this what I'm supposed to be looking for? Anyone have a pic of what I should be looking for? Any help is appreciated.

Pages: [1]