Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - mygt350

Pages: [1] 2 3 ... 6
1
1965 GT350/R-Model / List 3259 65 GT350 Carb fitting
« on: August 07, 2022, 06:13:29 PM »
I am in need of a fuel line fitting for a 65 GT350 List 3259 carb. It's the brass 1/8NPT to 7/16 fitting on pass side of primary float bowl. 1/8npt is male and 7/16 is female.
Thanks
Martin
5S228

2
Looking for useable metering blocks for a 65 List 3259 717 Holley carb as found on a 65 GT350. Stamped with part number 3903 on primary and 4560 on secondary.

3
1965 GT350/R-Model / 65 GT3560 Completion dates
« on: July 23, 2022, 02:35:20 PM »
Is there a list of build and completion dates for the 65 GT350's? I had the data for 5S228, but its filed away. n an undisclosed location...
Thanks
Martin
5S228

4
Wanted to Buy / WTB - 3259-1 Holley Carb Emulsion Tubes
« on: July 04, 2022, 11:23:01 AM »
I am looking for 2 Emulsion Tubes for a 66-67 3259-1 715 Holley metering block. This is a brass tube, about 1 1/2 inches long that presses into the two inner holes on top of a metering block, believe usually the front. Anyone have ones that are not plugged up and not damaged?
Thanks
Please PM what might have

5
1965 GT350/R-Model / 65 GT350 Alternator Ground Wire
« on: May 08, 2022, 04:59:11 PM »
Harness has a large black wire with red stripe that is a ground. Can someone tell me where correct mounting location for the lug is?
Its a 65 GT350

Thanks
Martin

6
1965 GT350/R-Model / 65 Hipo Engine Balance
« on: February 21, 2022, 04:30:38 PM »
When Ford balanced the 65 HiPo 289 rotating assembly, did they (Ford) include the flywheel and the thick balancer/hatchet, in the balance? I assume the balance excluded the balancer/hatchet and flywheel as those could be replaced during life of the engine without requiring a rebalance. 

Thanks in advance

7
1965 GT350/R-Model / 65 Hipo Distributor - A question of Dwell
« on: December 28, 2021, 11:14:10 AM »
Believe Bob Mannels book says to set points in a 65 dual point distributor to .019-.021 which should result in 30-33 degrees of dwell. If you blocked one set of points (A) and adjusted other (B) to 26 degrees dwell, moved block from A and moved it to B, then set dwell on A to 26 degrees, total dwell should be between 30-33 degrees when blocks removed. Would think dwell meter would be much more accurate than a feeler gauge. Thoughts?

8
Wanted to Buy / WTB DP-6 Points
« on: December 10, 2021, 08:40:39 PM »
I need 2 sets of points for a 65 C50E-12127-F hipo dual point distributor.
NOS in box, Points, DP-6 FDS-12171-N
Thanks

9
Wanted to Buy / WTB 65 HiPo Dual Point Distributor Components
« on: November 25, 2021, 04:18:17 PM »
Need to find some components for couple of a C5OF-12127-E 65 Hipo Dual Point distributors. Prefer NOS in box or exceedingly nice used parts.

1. Bushing, lower, C5AZ-12132-A MC-176.Need qty 2.
2. Points, DP-6 FDS-12171-N. Need 4, (2 sets).
3. Distributor gear, Need 1.
4. Spring clip that secures points cam (reluctor) to the distributor shaft. Need 2.
5. Coil wire,. Has molded grommet close to points connector. Need 2.
6. Points cam (reluctor) 13L/18L. C5AZ-12210-A. Need 2.

Thanks
Please PM or e-mail to mygt350@aol.com

10
1965 GT350/R-Model / 65 GT350 HiPo Distributor
« on: November 16, 2021, 03:11:02 PM »
Who is the current go to guy for rebuilding and setting up the 65 HiPo dual point distributor for a GTt350.  Have one that needs the right magic fingers to make it spot on correct for a 65 GT350.
PM or e-mail with reliable references/recommendations please.
mygt350@aol.com

11
Wanted to Buy / WTB-C4OE-6059-A Timing Cover
« on: November 01, 2021, 07:06:47 PM »
Looking for unmolested C4OE-6059-A timing cover with Mar or Apr (preferred) date code. This is the cover used with the alum water pumps on. 65 Hipo engines. Please PM me or send e-mail to mygt350@aol.com
Thanks

12
Wanted to Buy / WTB-1965 Small Letter Cobra Intake
« on: October 29, 2021, 07:42:21 PM »
Still looking for a nice unmolested 65 GT350 S1MS-9424A stamped intake with PCV port on rear runner. Please e-mail or PM me pics of what you might have hidden away.
Thanks
mygt350@aol.com

13
1965 GT350/R-Model / 65 GT350 PCV Grommet
« on: October 23, 2021, 05:04:39 PM »
Can someone tell me what the correct PCV grommet part number/marking is for a 65 GT350 open letter valve cover?
Thanks!
Martin

14
1965 GT350/R-Model / WTB 65 GT350 trunk mounted Autolite battery TAG
« on: August 22, 2021, 02:22:15 PM »
Am looking for the Autolite tag that was attached to the 65 GT350 trunk mounted battery/ Anyone have one to part with?
PM or e-mail to mygt350@aol.com
Thanks
Martin
5S228

15
1965 GT350/R-Model / 65 GT350 Trunk Battery
« on: August 22, 2021, 12:13:45 PM »
Did the 65 GT350 with rear trunk mount battery have red lettering  on case or was it completely black?

Pages: [1] 2 3 ... 6