Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Craner

Pages: [1] 2 3 ... 7
1
Wanted to Buy / Wanted NOS Door Weatherstrip, Right/Passenger
« on: November 10, 2023, 06:49:25 PM »
Wanted

1967,1968 Weatherstrip, Right Door

NOS weatherstrip:
Passenger Side Door, part number C7ZZ 6520530-A

Thank you
Fran

2
Wanted to Buy / NOS Heater Motor, 2 Wire, Non AC
« on: October 30, 2023, 04:15:17 PM »
Wanted: NOS Mustang Heater Box Fan Motor. Non AC application. 2 Wire
Stamped: 12v, Autolite
Ford PN: C5ZZ- 18527
Engineering PN: C5ZF-18527-A

Any assistance is appreciated.
Thank you
Fran

3
Wanted to Buy / Re: Hood Latch for 1968 Shelby
« on: October 24, 2023, 05:43:51 PM »
PM sent


Example photo from SAAC Forum member.. ( Thks Don)


4
Wanted to Buy / Hood Latch for 1968 Shelby
« on: October 23, 2023, 04:35:09 PM »
Wanted:
1968 NJ Hood Latch
Looking for production line hood latch
Correct stamping double A or W .
The most obvious place to find that stamping mark is on the outer facing safety catch. J shaped metal area.

Thank you.
Fran

Sourced with SAAC Forum members assistance!
Thank you.

5
Wanted to Buy / Re: Steel Wheel KH Made in Canada 15x6 Dated 1968
« on: October 06, 2023, 11:39:06 AM »
No longer available. 
Sorry.
Fran

6
Wanted to Buy / 1967,1968 Weatherstrips, Right Door, Rear Window
« on: September 25, 2023, 07:40:17 PM »
Wanted:
NOS weatherstrip:
Rear Window, part number C7ZZ 6342084-A
Passenger Side Door, part number C7ZZ 6520530-A

Thank you
Fran

7
Looking for suggestions on a place that can do this.. and that you have had good luck with the process, and turn around time.

Id like to put my original speaker back in my car as part of the car restoration.
Its in really good shape, I just dont trust the cone. (Original PN, dates etc)
Thank you
Fran

8
1968 Shelby GT350/500/500KR / Re: 4speed speedometer cable
« on: September 03, 2023, 01:25:07 PM »
The measurement on my 4 speed KR is 77 inches end to end(or very close)
See attached photos. Its a bit dirty, currently in as removed condition

9

This helps me confirm was is correct for a 68.

Greatly appreciate the help.
Fran

10
Question: Ive found 2 difference style switches used for the pop a way circuit actuation. 
This switch is actuated when the drivers door is closed. 

The switch used on my car needs to be replaced.  The plunger was damage, so Im searching for the correct switch. 

Were there different suppliers for this switch?
Or possibly the 67 and 68 Mustang tilt switch is different. 
The following is a photo of my damaged switch.

Any assistance is appreciated.
Thks
Fran

11
Wanted to Buy / Re: Steel Wheel KH Made in Canada 15x6 Dated 1968
« on: August 06, 2023, 06:56:05 PM »
Sourced.

Thank you.
Fran

12
Wanted to Buy / Steel Wheel KH Made in Canada 15x6 Dated 1968
« on: July 28, 2023, 04:12:50 PM »
WTB:  1 or 2 Kelsey Hayes Steel Wheels 15x6
Interested in what you have. I have a 67 that I might be willing to trade for a dated 68.
Wheels needed for KR.

 Thank you
Fran

13
Looking for suggestions for the orange color to match the original factory markings. 
I do have a good reference for the placement and size of the paint daub.
The orange coloring on my old rusty shock looked almost like a 60s Chevy Engine.
Its awkward to think id used that color :-)

I just got my shocks back from a complete rebuild, and ld like to add the factory ID orange paint marking to complete updates.

Thank you
Fran

14
Seeking suggestions on a chrome process/technique for an original chrome handle dipstick , stamped C7OE-6750-A.
My concern is how to remove the black end cap, and then reinstall it after chroming.
Has anyone had any luck doing this?

I dont want to mess up my original.
Comments appreciated.
This is for a 428CJ application GT500KR)
-attached photos if needed)
Thank you
Fran

15
Yes, heres a photo that I captured of that stamping. Its a little difficult to see, but using a decent light its there.  Also the rectangular Fomoco stamping about 90 degrees from the part number stamping.


Pages: [1] 2 3 ... 7