Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - plowhorse

Pages: [1] 2
1
Wanted to Buy / Re: NOS Upper and Lower Ball Joint Boots
« on: March 17, 2024, 01:09:05 PM »
Sorry, I think the NOS numbers should be C7OA
C7OZ is the repro number

2
Wanted to Buy / NOS Upper and Lower Ball Joint Boots
« on: March 15, 2024, 10:29:42 PM »
Looking for NOS C7OZ-3105-B and C7OZ-3105-A
Upper and Lower Ball Joint Boots
Not happy with the Carpenter repros













4
Are there inside pages also, or just front and back? Thanks!

5
1966 Shelby GT350/GT350H / Re: Seat Belt Anchor Plate Sealant
« on: March 01, 2021, 08:36:37 PM »
Thanks for the help. Question answered. I'd be lost without this Forum!

6
1966 Shelby GT350/GT350H / Re: Seat Belt Anchor Plate Sealant
« on: February 28, 2021, 11:37:55 PM »
Car was built mid- Jan 1966.
Don't recall any sealant on the plates when I took the car apart. It is an over ride car so the outer plates had been moved inward a bit. Just asking because I've always read the inner plates had been sealed.

7
1966 Shelby GT350/GT350H / Seat Belt Anchor Plate Sealant
« on: February 28, 2021, 09:42:09 PM »
Did the seat belt anchor plates under the car have any type of sealant applied to them? Thanks

8
1966 Shelby GT350/GT350H / 66 Radio delete
« on: January 14, 2021, 05:04:14 PM »
This may be a silly question, but would a radio delete car still have come with a speaker? I'm guessing not.
Thanks

9
1966 Shelby GT350/GT350H / Re: Rear quarter Window Interior Trim
« on: November 22, 2020, 11:51:52 PM »
I have a set from the above mentioned guy from California.
While the texture was very accurate, they were about 3/8 inch short of fitting in my aluminum quarter window frames.
For Sale if anybody wants them.

10
Had the same exact issue in Dec. of 2018, so you are not the first. Apparently my words fell on deaf ears. Was happy with the fit of the molded part, but the outer edges weren't even close. Lots of trimming involved. How hard can it be to cut a trunk mat to the proper shape?

11
Wanted to Buy / Re: 289 Block
« on: November 22, 2018, 08:01:27 PM »
Narrow range... needs to be 5M to early 6A
But thanks to everyone for offering up what they have!

12
Wanted to Buy / Re: 289 Block
« on: November 21, 2018, 08:28:12 PM »
TLea...pm sent

13
Wanted to Buy / Re: 289 Block
« on: November 21, 2018, 03:56:11 PM »
TLea … 6A3 would be good. Where are you located?

14
Wanted to Buy / 289 Block
« on: November 21, 2018, 01:54:40 AM »
WTB 289 Block with 5M or early 6A date code.

15
Wanted to Buy / Re: 1966 Shelby 1/4 window trim
« on: August 12, 2018, 11:23:06 PM »
I warmed our warped ones up then clamped them in between some 1x4's to cool down. Ended up perfectly straight but also shrunk 3/4 inch in length!
 

Pages: [1] 2