SAAC Forum

Hello Bob.
Thanks for the reply the pivot on the outside of the quarter vent window frames isn't to bad  just really bad handles inside that's why I'm looking for nos ones for each side.
Also looking for a nos 67 mustang heater blower motor switch non ac. # C7ZZ-18578-A
If anyone can help.
Thanks again everyone for any help given.
Have a nice day
Dave

Hello everyone
I am looking for the following items and thought I would ask here first.
If anyone can help me I am looking for the following NOS ford items.
1x nos 67 mustang/ shelby front LH vent window frame handle #C6OZ-6222917-A
1x nos 67 mustang/ shelby front RH vent window frame handle #C6OZ-6222916-A
1x nos 67 mustang/ shelby front doors and ignition lock set #C9AZ-6222050-A
1x nos 67 mustang / shelby heater blower motor switch non ac #C7ZZ-18578-A
If anyone has the following items for sale or can help with leads in anyway please pm me.
Thank you all for your help.
Have a nice day
Dave

Hello everyone
I am currently looking for a ford 390 fe bare engine block standard bore hydraulic lifter motor (1966) and up.
If anyone in pa has one( as that's where I'm based) and will be attending the Hershey show next week i could collect from the show and pay in person if preferred or pick up directly.
Pm if you have one for sale with the price.
Any help or leads are much appreciated.
Many thanks
Have a nice day
Dave

Thank you for the lead.
I contacted Bill Heeley and he only deals in 4 speeds but thank you for the help any leads or information is much appreciated.
Many thanks
Dave

Hello Everyone.
I am currently looking for a 1967 shelby gt500 shifter mechanism for a customer.  I believe these shifter mechanisms had a extra piece weld on them as part of the special handling package available on mustangs I believe? I maybe wrong on that.
If anyone has one for sale please contact me and send me a pm.
I know this is a long shot and I'm sure they are hard to find however if you don't ask you never know.
Any help, information or leads are much appreciated as always.
Thank you for your time.
Have a nice day
Dave

Hello
I have friend that is looking to purchase a 1968 shelby gt350. I forwarded him the 68 shelby registrars name and email address however I was wondering if anyone might have a contact number for the 68 shelby registrar  Vincent Liska.
Thank you all for any help you may be able to provide.
Many thanks
Have a nice day
Dave

Randy and shelby Doug.
Thank you for the responses.I went on cobra automotives website today and could not find their 427 fe harmonic balancer listed anywhere? Do you have a part number or a web link you could post to the item.
All I found on their website was a professional products balancer.
Thank you all for your help.
Have a nice day
Dave

Hello everyone
I hope I have posted this question in the correct area. My apologies if it is posted in the wrong place.
I am currently building a fe engine from scratch and am looking at buying a new 427 fe style harmonic balancer.
I have found two brands so far scat #sca-8009. And professional products #80009 both are the street brand rated safe to 6500 rpm non sfi approved.
They then make some slightly more expensive ones that are Sfi approved and rated good to 10000rpm well beyond my fe (6000rpm max) I believe you just change the 8 in the part number to a 9.
My question is has anyone used these brands and what was your experience?  Would you buy a sfi approved harmonic balancer instead even for a street motor? or can someone recommend a different route to go.
Thank you all very much for any help,advice or guidance you can give me.
Thank you very much
Have a nice day
Dave.

Hello 427 Heaven
Thank you for the reply I do not currently need a bell housing just the engine block but thank you very much for the offer.
Thank you for your help it's much appreciated.
Have a nice day
Dave

Hello Karl
Thank you for the reply I have sent you a PM.
I await your reply.
Many thanks
Dave

Hello everyone
Both sets are currently sold and spoken for.
Thank you everyone for your help.
Have a nice day
Dave

Hello everyone.
I am currently looking for a non-hipo ford 289 engine block with main caps with the early 5 bolt bell housing bolt pattern. Standard bore would be nice however all offers considered.
I am based in Pennsylvania and will be attending the fall Carlisle car show and Hershey show so I could collect and pay in person at either of the shows if preferred.
I would like to try and find one if possible in pa or nearby.
Anybody with any help or information or contacts that could help me locate one would be much appreciated.
Even if it's a short block/long block or complete engine and leads appreciated.
Thank you all once again for your help.
Have a nice day
Dave

Hello everyone.
My dad has for sale two pairs of the Lucas 8 inch fog lights that was used on the 68 Shelby's and 69 Shelby's I believe also.
These fog lights are new in the original Lucas boxes.  They came from a dealership in England that sold bentleys and apparently some bentleys also used these fog lights also.
The chrome is in fantastic condition as you can see from the photos. They also come with the black plastic covers for the lights.
Now I do believe these are not factory assembly line correct units however I do believe they could be used for a daily driver or clone or maybe someone who wishes to save their originals and use these instead.
Again these are not factory assembly line correct however I thought I would offer them for sale here first before I put them on eBay in case anyone can put them to good use instead of sitting on a shelf.
The price is $300 for a pair or $500 for both pairs( 4 in total)
I will be attending the fall Carlisle car show in Pennsylvania if you wished to collect and pay in person.
If you have any questions please email me.
Many thanks
Have a nice day.
Dave

Hello Everyone
I am placing an advert on behalf of a friend.
My friend is currently looking for a good 1968 mustang/shelby front drivers side bucket seat( both base and back) as good core to rebuild( new seat covers /new foam ect)
Anyone in the state of pa that has one would be a bonus as it's nearer however any help or leads are much appreciated.
Many thanks everyone for your help.
Have a nice day.