what is the length of 69-70 gt350 air cleaner stud.... did shelby or ford change out the stud for the taller fa-50 element, because the factory stud is too short(regular 351w used a fa-41 and a completely sealing air cleaner lid)...thx keith
- Welcome to SAAC Forum.
News:
SAAC Member Badges are NOW available. Make your request through saac.memberlodge.com to validate membership.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
#17
Wanted to Buy / Re: Wanted original distributor lead..orange boot
April 18, 2023, 03:52:34 PM
found,thx
#18
Wanted to Buy / wanted diamond (LH) WHEEL WEIGHTS
April 18, 2023, 03:51:54 PM
wanted original diamond,LH, wheel weights...need assorted sizes .25,.5,.75,1etc.... thx keith 318-393-1502
#20
1969-1970 Shelby GT350/500 / Re: distributor lead color
April 08, 2023, 07:59:01 PM
Figured it out,orange,thx
#21
Wanted to Buy / Wanted original distributor lead..orange boot
April 07, 2023, 05:08:05 PM
Wanted original distributor lead with orange boot for 70 351w distributor...single lead orange boot...thx keith 318-393-1502
#22
1969-1970 Shelby GT350/500 / 69 shelby wheel weights
April 03, 2023, 02:36:39 PM
what do the experts say on shelby wheel weights....diamond(LH),micro ,etc ...and on front and back of wheels....remember theses wheels were installed at A O SMITH not ford...eager to hear...thx keith
#23
1969-1970 Shelby GT350/500 / Re: distributor lead color
March 31, 2023, 09:51:16 PM
4 speed transmission
#24
1969-1970 Shelby GT350/500 / distributor lead color
March 31, 2023, 04:11:01 PM
1970 gt350 ...what is the correct color on the distributor lead boot(goes to coil)...remember this distributor was changed during 70 year conversion and stamped ED and had a dual vacuum advance...thx keith
#25
Wanted to Buy / wanted nos 1969 heater valve
February 22, 2023, 12:04:42 PM
wanted nos or really nice working used 1969 heater valve ,need c9 number part,which has the brass body vs plastic ,thx keith 318-393-1502
#26
Concours Talk / Re: 69 GT500 stone guard
February 14, 2023, 03:20:55 PM
the front black edge is the bumper filler piece(actually two(2) pieces),attached by screws to the stone guard(like tail panel screws)...believe jack brooks at dead nuts on sells this filler(flexible material)
#27
Wanted to Buy / Re: wanted wittek tower clamps size 1 1/16...dated 4/68 or 1/69
February 03, 2023, 11:20:10 AM
bump
#28
Wanted to Buy / wanted wittek tower clamps size 1 1/16...dated 4/68 or 1/69
January 13, 2023, 12:41:10 PM
wanted 6 used original tower clamps...1 1/16 size...dated 4/68 or 1/69 ..used on heater hoses...thx keith
#29
1969-1970 Shelby GT350/500 / 1969 shelby gt350 carburetor base gasket part number
January 10, 2023, 04:28:52 PM
need help...does anyone know the part number for the thin blackish carburetor base gasket(2 used,one above and 1 below spacer), on the 69(70) gt350 ? thanks keith...ps i have one that came with my nos spacer, but i dont know the part number...thx again
#30
1969-1970 Shelby GT350/500 / Re: Master Cylinder Cap
January 06, 2023, 02:23:17 PM
to clarify venting...no vent in middle of cap....2 diagonal corners have vents on cap lip...later years ,1 vent on lip,even later vent in middle