SAAC Forum

Hi, any idea which car this was on the chips tv shows pilot ?

https://m.youtube.com/watch?v=h2OPgvXWuV8

Here is the video they shot.

I went from the normal cars and coffee in Henderson over to the Shelby cars and coffee in Vegas- mostly newer Shelby cars and kit cobras but still cool - they all appreciated the 69 - hard to believe there are not more Shelby's here in Vegas? At least down here they know what the gt500 is, when I had it up north in Reno people thought it was a custom car Oh in Reno 6S853 is a red mustang.

Is this from 65 or 66?

I will start

SFM6S1172 is for sale anyone interested should study the following images.

In person inspection advised!

I would like to say a public thank you to BGlover for the centerpiece on my F.I.V. Wheel, 853's interior never looked better!

Dennis Collins now claims his 67 mustang is 1477  - Dave ?

 8T03S179579 fyi to the owner scam listing- https://phoenix.craigslist.org/cph/ctd/d/sioux-falls-1968-shelby-gt500/7470836071.html

Would a 1966 over the counter wood wheel have come with the gt350 and cobra horn button or the CS button? 

Hi all, does anyone have a 68 gt350 with a SA mexican block? The claim is SA produced an over the counter 68 hipo 302 that was based on the mexican 302 with the larger main caps.  Can anyone shed light on this ?

Looks like a bogus sales add listing 6S1533 for sale, anyone know the owner ?

I have recently seen a number of wanted posts for 66 gt350's, the common thread is that the people posting these wants (for the most part) are looking for a car below it's market value, in some cases less then 50% of market value.

The question is, would owners here on the saac forum sell their car for a reduce price because the buyer is on the saac forum as well?

Hi all, debating on a t5 conversion so I am looking for some who has done it.

I would be going from a t10 to a t5z and I want to use the adaptor plate so I can run the original bellhousing and linkage.

Questions:

Do I need to shorten the drive shaft ? If so by how much ? or is there an aftermarket bolt in?

Does the trans tunnel or shifter opining need to be modified?

What conversion kit did you use?

Thanks!

Hi all,

so the calipers knocked off the stick on weights again, this is the second time using the thinnest weights. Has anyone had success with wheel weights on 10 spoke Shelby wheels, if so can you post a photo of the weights you used..

Thanks

I must first start with the good quality reproduction gas gap that always bothered me because the snake looks to be missing a chromosome. So the hunt began for a NOS service part  S2MS-9030-A, it didn't take long before it was in my hands and on the car. To my surprise when they made the cap they put it together wrong and the snake was upside down! I compared it to the old and thought no big deal I'll just bend the large tab and spin it around, no dice! The stud for the cable prevented the cap from rotating to the upright position, oh and the tab snapped off. So out came the Dremel and off came the studs that hold the cap together. I re-drilled the mounting holes, used the miller 211 to weld on new mounting ears and weld the ends of the mounting studs to hold the cap together again and voila ! A nos-ish pos part...... But at least the snake looks healthy.     

Just wanted to say thanks in public for Randy's help and sharing of knowledge !

https://www.ebay.com/itm/1966-Ford-Mustang/254721853160?hash=item3b4e9b06e8:g:xggAAOSwwH5fY8bL

Calling the owner of 6S622 ebay scam using your vin number!

Anyone have a car with original floor mats ? I would like to find out what was used.

Hi, what's the usual lead time on block casting dates to vehicle order date?