SAAC Forum

Hi all,

There were Original 67 Shelby GT500's with an engine block C6ME-A 428 block with a cast 66-427 in the bellhousing face and an A scratch next to the cast 66-427 please?

Any help please?

Thanks Kyle.

Hi all,

I am looking for the engineering numbers for early vs late 67 Shelby GT500's.

I need to know the Engineering numbers for these parts.(For a Special Police Interceptor engine.)

:Camshaft
:Crankshaft
:Crankshaft main bearings caps
:Pistons
:Connecting rods
:Connecting rods caps
:Oil pan

Any information please?

Thanks Kyle.

Hi all,

I am looking for these parts. I need all Original parts Used or NOS in good condition. I need a 3/4 Jack dated 6K, 6L or 6M for Kelsey Hayes mag star wheels, under dash guages pod (only the pod), trunk dash or grille (2) or (3) plastic chrome emblems for GT500, AMP junction block C5VB-14448-A not broken and with screws, EC7ZX-A clutch fan preferred restored , NOS power steering hose C77Z-3A713-B, (2)NOS air cleaner wing nuts, Throttle Return Spring Bracket and PCV Hose Clamps (2) size 1/2 inch.

Anyone who have these parts send me an email kylezammit123@gmail.com or pm send.

Thanks Kyle.

Hi all,
I need a set NOS DP-6 points marked AUTOLITE with dark grey insulators.

Contact me: Email kylezammit123@gmail.com or PM me here on SAAC.

Thanks Kyle.

Hi all,

I need an Assembly line early NOS 2X4 air filter Marked Autolite - black rubber - with wire mesh.

Anyone who has one please send me a PM sent or send me an email kylezammit123@gmail.com

Thanks Kyle.

Hi all,

I am looking for an Original 67 Shelby GT500 Gas Cap emblem in very good condition or NOS.

Anyone who have one let me know please?
PM send or send me an Email kylezammit123@gmail.com

Thanks Kyle.

Hi all,

I am looking for a good condition that need's restoration or restored, radiator marked FOMOCO San Jose non A/C for Automatic dated late 1966 November or early December.

If anyone has one let me know please.
Contact me via PM sent or Email me kylezammit123@gmail.com

Thanks Kyle.

Hi all,

I am looking for a pair Original 67 Shelby rear anti wrap up snubbers blocks in good condition.

Thanks Kyle.

Hi all,

I am looking for a 2X4 sand cast bottom lid with the PCV elbow curved tube or elbow square tube.

For an early 67 Shelby GT500.

My Email kylezammit123@gmail.com

Thanks Kyle.

Hi all,
I am looking for a five Original good condition Kelsey Hayes Mag Star wheels all dated late 66, All for an early Mustang 1967 Shelby GT500.

Please send me PM or Email me kylezammit123@gmail.com

Thanks Kyle.

Hi all,

I have a question about my early 67 Shelby GT500.

My car was ordered on 11/08/66 and realised from San Jose 12/28/66.
Completed by Shelby 1/25/67 and shipped 1/30/67.

My question is:
My engine block casting date code is 6H19 and assembly date of the engine is 6J28 9. The chylinder heads casting date is 6J 13 and the other one is 6J8.

My engine is a correct date code for my car please?

Thanks Kyle.

Hi all,

I have this exhaust manifold and it has a cutting are.
Is this from factory or a past owner modification?
I need to know from protection line were for a Mustang 1967 Shelby GT500?
I am referring were there is the red.
Thanks Kyle.

Hi all,
I have a NOS heater connector elbow and I need to know what exactly from production line were.
They were yellow zinck plating, silver plaiting or painted please ?

Thanks Kyle.

Hi all,

There were types on a Shelby GT500 windshield washer reservoir bag ?
I think there are types from the back side.
Here are some photos.

Thanks Kyle.

Hi everyone,
I have this throttle linkage rod and I don't know if it is original or reproduction and if it's correct for a 67 Shelby GT500?
It was silver zinc plating or metal grey coating ?

Thanks Kyle.

What is the correct power steering pump pulley for a Mustang 1967 Shelby GT500 ?

Thanks Kyle.

I have this Shelby guages pod and I don't know if it is original or reproduction.
Thanks Kyle.

I need all original parts 2X4 Cobra air cleaner , dual point distributor (C5AF) dated late 1966 , FE 390GT or 428PI exhaust manifolds dated late 1966 , rear antiwrap up snubbers , pinion snubber , front 2 piece nose fiberglass , C7ZA engine mounts insulators and Big block radiator for automatic dated late 1966.

Thanks Kyle.

Wanted: I need a dual point distributor C5AF-12127-E dated late 1966 , exhaust manifolds FE dated late 1966 and rear antiwrap up snubbers all for a Mustang 1967 Shelby GT500 please?