Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - imming1965

Pages: [1] 2 3 4
1
1969-1970 Shelby GT350/500 / bracket identification
« on: March 21, 2024, 03:59:50 PM »
I need help figuring out what these brackets are for or if they are even for this 1969 shelby gt350 convertible? maybe interior quarter panel brackets?

2
1969-1970 Shelby GT350/500 / convertible alignment pins
« on: March 04, 2024, 10:28:37 AM »
are 1969-70 convertible top alignment pins unique to 69-70? does anyone have a picture of them? if so does anyone have any they might part with, thanks Jeremy

3
1969-1970 Shelby GT350/500 / a/c box attachment washer
« on: March 01, 2024, 11:33:31 AM »
can anyone tell me the correct size washer and finish for attaching a/c - heater box. I think the washer I have is close but might be a little to small?

4
1969-1970 Shelby GT350/500 / convertible roll bar hardware
« on: February 06, 2024, 08:59:08 AM »
can some give me a picture of the correct hardware for the ro bar mounting on a 69 gt350 convertible? thanks Jeremy
    also I'm still looking for a picture of the side scoops removed so I can see how and what kind of tape was used to apply them.

5
1969-1970 Shelby GT350/500 / another part question about convertible
« on: January 26, 2024, 10:20:23 PM »
I think I am missing a part but don't know for sure. the assembly manual does not have a good picture either. is there a bracket that I may be missing that goes between the power top motor and the trunk floor?
   pictured below is the motor and the floor which it goes. holes don't line up and in assembly manual it looks like there might be a bracket.
     does anyone have a picture of this bracket? or an I missing or have wrong motor? thanks  Jeremy

6
1969-1970 Shelby GT350/500 / part identification
« on: January 26, 2024, 10:58:23 AM »
hey can I get some help identifying these brackets and there location? I'm restoring my first 69 shelby convertible and I didn't take it apart. I can't figure out these pieces. thanks
   pictures arrached

7
can anyone provide good pictures of 1969 GT350 with automatic transmission. finishes and appearance photos.
Pan Natural? color of dip stick? etc?

8
1969-1970 Shelby GT350/500 / side quart scoop install question
« on: January 11, 2024, 09:48:05 AM »
I have been told that the side scoops on a 1969 shelby were installed using white double sided tape. is this correct? also if it is, does the tape go all the way around? does anyone have pictures of how the tape was installed on scoop? I'm restoring this early 69 gt350 and wasn't the person whom disassembled this car so I'm a little behind the 8 ball and figuring out a lot of these details because I don't have any reference pictures to go from. I usually take hundreds of pictures so when assembling I can refer back.

9
1967 Shelby GT350/500 / best choice headlight???
« on: December 12, 2023, 09:29:03 AM »
What is the consensus on correct aftermarket headlight to use for judging? embossed ford logo? engraved ford logo?
Also did shelby use different styles depending on when car was built? thanks Jeremy

10
1967 Shelby GT350/500 / in board grill and support question
« on: November 07, 2023, 10:04:14 AM »
I'm restoring an early April completion date gt350 with inboard lights. so has big hole grill pattern. in pictures you will see 1/8" rivets with spring clip used as washers. This car has had front end work and has been changed from original but I wanted to make sure this was not a thing. I cannsee why they used the clip to help hold the lower grill in but have a hard time believing this is correct, I'm guessing the 3/16" rivet with big head would have been correct. can someone help with what I'm seeing is probably not correct in picture. thanks jeremy

11
Wanted to Buy / 1967 15' steel wheels
« on: October 05, 2023, 01:48:31 PM »
i'm looking for either 11/66 or 3/67 steel wheels. trying to make a set. i have one 69 date code and one 70 date code im willing to trade or i could trade the 67 date code ones to help someone else match a date also
      wheels i have and date
      1- 11/66 three knub 15x6
      1- 3/67 three knub 15x6
      1-69 four knub  15x6
      1-70 four knoub 15x6

12
1969-1970 Shelby GT350/500 / 69 gt350 rearend vent
« on: September 05, 2023, 04:38:21 PM »
hey I'm looking for pictures and measurements on the location of rear end vent, The 1969 gt350, I'm restoring didn't have rear end, I picked one up but was told it was from a big block car and they were different from small block??? so I need location of vent if this is true so I can relocate it. thanks Jeremy

13
Wanted to Buy / 1967 headlight retaining rings
« on: August 14, 2023, 03:09:46 PM »
I'm looking for (4) headlight retaining rings (stainless part that holds light in bucket) I have some but would like to find better ones

14
1967 Shelby GT350/500 / Functional lower scoops question
« on: August 10, 2023, 05:50:42 PM »
Has anyone seen lower scoops attached like this? i'm restoring this january 67 gt350 with funcational lower scoops and i can not figure out how these were installed the way they are. i can only assume the inner part was installed and then the outer part was glued on. because there is no way to get rivet gun inside scoops to install the rivets??? quarters are original and it appears the scoops have never been taken off and reinstalled. anyone seen these scoops installed this way before? any ideas or thoughts?

15
I'm having an fitment issue on the taillight assembly for a  1967 Shelby I am currently restoring. I'm looking for several answers for basically the same question
    I pretty sure I have the wrong combination of parts and that's why it's not fitting correctly. And I also already know as most of us with these cars, that are are several changes and versions to deal with according to when it was built..
      I am working on March built car and need to know correct version of taillight panel, trim type and inner bracket combination for that time frame?
     I have raised panel, taillight panel with studded trim bezel with flat  or L shaped inner bracket now and as in picture below you can see it doesn't want to go far enough in to pop rivet up. So I'm guessing I need the other inner brackets to fix this issue. But I want to make sure I have the correct outer parts for when car was built....
      Could use some knowledge of this taillight changes and combinations of parts, thanks Jeremy

Pages: [1] 2 3 4