SAAC Forum

Anyone know of a good Fe engine builder in the Chicagoland area?

Thanks

Looking for the following parts...

1 - leaf spring snubber plate
1 - 289 HiPo head C7ZE, NON SMOG
Early tail light steel mounting buckets

Thanks and please send me PM.....

Looking for the 67' Passenger side grille mounting bracket....    Does anyone repop this bracket?
Quarter panel fiberglass end caps
C7ZE HIPO head date coded around Dec,1966
1 - early aluminum tail light trim, without screw holes

Thanks

I have a set of new Ford NOS coil springs with the following Ford parts tag on them C7ZZ-5310-BB.  I bought these years ago for my car but I can't find this Ford number in any of the Ford parts books.  They also have a Gary/Yellow strip on them.

Can anyone tell what the application is on these springs?

Thanks

Question, was ATF Plastics one of Shelby's fiberglass parts suppliers?

Also, on Ebay there is 67 fiberglass hood. item# 174567655817  Does this look like an original hood or old Repro?

Thanks

Looking for a NOS set of 1967 End Caps of or nice used drivers side.

Please send me PM, Thansk

Looking for C7ZE 289 HiPo head with built date around 6M non smog.

Please send me PM.   Have cash or many other NOS for possible trade.

Thanks

Can someone tell me how to identify a set of original exhaust chrome tips?  Is there a part number on them or certain way they are made?

Thanks

Looking for 1 C7ZE HiPo head date coded around 6M... Also looking for 1 Tail Light Aluminum trim ring.  Early style without screw hole..

Thanks and please send me PM...

Anyone have any idea what it costs to restore a set of 4 Mag Star rims in good driver condition and also who restores them?

Thanks

Looking for paxton Cobra air box.  I have an NOS 68' paxton box (SHELBY) for possible trade or I have $.

Also might be interested in a set of gauges if the price is right....

Thanks and please send me PM

Does anyone know what yoke Ford used with the SPEC rear end case?  1310, 1330 or 1350

Thanks

Anyone know of any tricks on removing frozen studs out of the aluminum tail light frames?  Some of the studs are broken off already just above the face of the frames.

Thanks

Looking for the following 67' GT350 parts:

1 - C7ZE 289 HiPo head, non-Smog with built date Dec. 1966 (6M)
1 - C7ZA 289 NOS Motor mount
Passenger Side curved grill mounting bracket
Early Steel inner tail light mounting plates
NOS rear quarter panel end caps
Holley Carbs,  C6OA-A or C6OA-B

Have cash or many other 67' for trade,,,,  Thanks

Looking for the following 67' parts......

289 C7ZE HiPo Head, prefer non-smog
Early tail light aluminum frame without screws holes
NOS, Quarter panel end caps
RT front hood pin mounting bracket
Underdash aluminum gauge pod and wiring
Paxton Cobra Carb Air Box

Have cash or other parts for possible trade.....  Please send me PM...

Thanks

Looking for the following parts:

1- C7ZE 289 HiPo head
Aluminum tail light trim frames
NOS- Quarter Panel End Caps
Tail light inner truck metal mounting brackets

Thanks and please send me PM....

Anyone have any kind of idea what an original GT350 289 Hipo engine would be worth, Air cleaner to oil pan all date coded Dec. of 1966.  Engine is taken apart but all original/ complete and still  standard bore.  What would the Rug-N trans with shifter also be worth?

Thanks

Looking for 289 HiPo head C7ZE Non Smog

Thanks

What are the correct fasteners for inboard headlight buckets?

I own an early February GT350 and the car does have inboard lights. My lights have 3/16 x 1/2 hex bolts with lock washers.  Are these the correct fasteners? or is slotted sheet metal screws correct?

Thanks

Looking for the Carter carbs that was sold over the counter on the 289 2X4 Cobra Intake setup by Ford.

Think, correct carbs are Carter's 3258s and 3259S stamped on the right front mounting flanges.  Also, looking for fuel log, chrome air cleaners and linkage..

If anyone has any of these parts or single carb, please send me PM trying to put a setup together for my car. 

I only have the intake @ this point...

Thanks