Author Topic: Autokraft Mk IV  (Read 3107 times)

danielw356

  • Newbie
  • *
    • View Profile
Autokraft Mk IV
« on: September 03, 2018, 01:05:21 PM »
I am the original owner of a 1989 Autokraft Mk IV (#1297).  It has very low miles (1260!), but it also has a leaking wheel seal on the rear axle.   The brake pads are damaged.  Does a service manual exist?  Does anyone have one?  Does anyone know the specs for replacing the seals and brakes pads?   Any help or advice is appreciated.   Dan

98SVT - was 06GT

  • SAAC Member
  • Hero Member
  • *
    • View Profile
Re: Autokraft Mk IV
« Reply #1 on: September 03, 2018, 01:51:51 PM »
I would have figured all European Ford parts as the were helping Angliss with these. Found this over on Club Cobra:

Mk IV Brake Info:

Vented Brake Disc Rotor: AC - Front rotors are 11.5" in diameter, 7/8 thick and ventilated, 6 pin threaded to hubs, 1/2 inch tophat, 1" bottom offset. Steve Gray at Brooklands has the rotors. They are based upon production units, but are modified. Brooklands Motor Company Front Page

Front Brake Calipers:   BMW E23, Model 735 Years: 03.77 - 07.86   ATE # 13.0460-9031.2; trade #’s 20437 & 609031   

Front Brake Pads: BMW 7 Series 1976-86   ATE - 13.0460-9031.2 Brake Pad Set, disc brake. Width:89.9 mm, Height:70.5 mm, thickness/strength:19 mm, wear indicator prepared, ATE

Rear Brake Caliper:   Peugeot 505 (early 80's station wagon) Peugeot 504/505 part #’s-- 4400.11 and 4400.12   
Girling part #’s– 64033853 and 64033854   They are Girling AH12 MK3 types– TRW/Lucas part #’s– BCT 125 and BCT 126
BECK/ARNLEY Part # 0770640S.   Beck Arnley part number for the right rear Peugeot caliper (for the left side of the Mk IV)

Rear Brake Caliper Repair Kits:   Peugeot part # 4449.15 Some AKL cars used AP brakes. Lucas part # SP 2582

Brake Booster Servo:   Ford Sierra MK1/MK2 Brake Booster Servo ‘Girling’ 1982 - 15/2/1993, Ford part # 6195975   Brake booster info– email Bob Green at BG Developments - manufacturers and suppliers of competition and high performance braking systems for over 30 years (New G/Ford booster)

Brake master cylinder: ( 2 versions-7/8"or 13/16" bore) **   1972-76 MKI Ford Granada   Girling part # G 64679152Q123 X, original Girling part # 64066627, new reference # PMH117 **part # stamped on the brake master cylinder
« Last Edit: September 03, 2018, 01:53:44 PM by 98SVT - was 06GT »
Previous owner 6S843 - GT350H & 68 GT500 Convert #135.
Mine: GT1 Mustang Track Toy, 1998 SVT Cobra, Wife's: 2004 Tbird
Member since 1975 - priceless

danielw356

  • Newbie
  • *
    • View Profile
Re: Autokraft Mk IV
« Reply #2 on: September 04, 2018, 01:30:18 AM »
Thanks for the detailed information (and the new contact).   My tech will be a very happy guy.   Neither of us realized the vast array of manufacturers for these components.  Thanks again.  Dan

1bigfish

  • Newbie
  • *
    • View Profile
Re: Autokraft Mk IV
« Reply #3 on: September 21, 2018, 09:45:58 AM »
I also own an AC MKIV. Post your concerns on the AC Owners forum for information. Cobra Restorers (cobrarestorers.com) in Kennesaw Georgia can make any repairs or service.

danielw356

  • Newbie
  • *
    • View Profile
Re: Autokraft Mk IV
« Reply #4 on: September 21, 2018, 10:12:46 AM »
1bigfish, 
Thanks for the advice  -  hope to put a few more miles on mine before the cold weather sets in.   Hope you are enjoying yours for the rest of the season. 

Re: Autokraft Mk IV
« Reply #5 on: November 21, 2018, 04:33:58 AM »
Hi Dan,

if You still need some parts info about the MK IV just drop me an pm or mail.

I own AK 1106 and did a complete car rebuild by myself.

Uwe

Sean S

  • Newbie
  • *
    • View Profile
Re: Autokraft Mk IV
« Reply #6 on: January 29, 2024, 12:56:28 AM »
I'm looking for a brake master cylinder for a 1990 Autocraft Cobra. please tell me.[/img]

Bill

  • SAAC Member
  • Hero Member
  • *
    • View Profile
Re: Autokraft Mk IV
« Reply #7 on: January 29, 2024, 08:42:16 AM »
I'm looking for a brake master cylinder for a 1990 Autocraft Cobra. please tell me.[/img]

The OP was Last Active: September 21, 2018, 10:12:07 AM  ::)

Perhaps if you read this first:
https://www.saacforum.com/index.php?topic=25725.0
You would not make a poor first impression.


Bill
Instead of being part of the problem, be part of a successful solution.
HOW TO IDENTIFY A FORUM TROLL
https://www.saacforum.com/index.php?topic=16401.0

FL SAAC

  • SAAC Member
  • Hero Member
  • *
  • Posts : 22092
    • View Profile
Re: Autokraft Mk IV
« Reply #8 on: January 29, 2024, 08:51:44 AM »
I'm looking for a brake master cylinder for a 1990 Autocraft Cobra. please tell me.[/img]

Sean welcome to the forum. Hope you find your master cylinder
Home of the Hertz Musketeers

These cars are meant to be driven so enjoy the hell out of all of it. not just the look of it when its all clean.CS

A person without a sense of humor is like a wagon without springs.It's jolted by every pebble on the road

I have all UNGOLD cars

Life is short B happy

rkm

  • Full Member
  • ***
    • View Profile
Re: Autokraft Mk IV
« Reply #9 on: January 29, 2024, 12:01:27 PM »
Try Pegasus .

tesgt350

  • Hero Member
  • *****
    • View Profile
    • FRIENDS OF THE HAWK
Re: Autokraft Mk IV
« Reply #10 on: January 29, 2024, 12:13:36 PM »
I'm looking for a brake master cylinder for a 1990 Autocraft Cobra. please tell me.[/img]

The OP was Last Active: September 21, 2018, 10:12:07 AM  ::)

Perhaps if you read this first:
https://www.saacforum.com/index.php?topic=25725.0
You would not make a poor first impression.


Bill

Not a poor first impression, He is looking for a Part for the same Make & Model Car so he is just restarting the conversation instead of starting a whole new Post.

Bill

  • SAAC Member
  • Hero Member
  • *
    • View Profile
Re: Autokraft Mk IV
« Reply #11 on: January 29, 2024, 12:20:39 PM »
I'm looking for a brake master cylinder for a 1990 Autocraft Cobra. please tell me.[/img]

The OP was Last Active: September 21, 2018, 10:12:07 AM  ::)

Perhaps if you read this first:
https://www.saacforum.com/index.php?topic=25725.0
You would not make a poor first impression.


Bill

Not a poor first impression, He is looking for a Part for the same Make & Model Car so he is just restarting the conversation instead of starting a whole new Post.

Yet none of the participants have been here on the forum since 2018
He did the same thing on another forum, only it has been much, much, much longer with the person he was asking a question towards being deceased, over 10 years .  ::)  :-[

Hence the "Newbie read this" post and guidelines.

Bill
Instead of being part of the problem, be part of a successful solution.
HOW TO IDENTIFY A FORUM TROLL
https://www.saacforum.com/index.php?topic=16401.0

Royce Peterson

  • Hero Member
  • *****
    • View Profile
Re: Autokraft Mk IV
« Reply #12 on: January 29, 2024, 04:05:42 PM »
I'm looking for a brake master cylinder for a 1990 Autocraft Cobra. please tell me.[/img]

This was posted above - seems like a very common part available basically anywhere and everywhere.

"Brake master cylinder: ( 2 versions-7/8"or 13/16" bore) **   1972-76 MKI Ford Granada   Girling part # G 64679152Q123 X, original Girling part # 64066627, new reference # PMH117 **part # stamped on the brake master cylinder"
1968 Cougar XR-7 GT-E 427 Side Oiler C6 3.50 Detroit Locker
1968 1/2 Cougar XR-7 428CJ Ram Air C6 3.91 Traction Lock